29 comments

Hi, about 8,5h with 0,16mm layerheight. With modern printers it should be faster

Hello, thank you for your inquiry. No, unfortunately, that's no longer possible. The air filter box is designed for racing use.

Hi, thank you for your inquiry and the download :) We'll manage it. No worries. Removing the support structure from the pony is very complex - even if the settings are perfect. I assume you are using PLA and want to print the pony with the base? First, we need to find out what layer height you are using, what print temperature, and at what speed you are printing. I recommend a layer height of 0.16mm for the pony and a speed of 45mm/s for the outer walls and 60mm for the inner walls and infill. The support structure should be printed at 30mm/s. Figures always need to be printed slowly. I will first generate a test model for you, with which you can test which settings for the support structure work best for you. Only then will we start with the pony, okay?

OK, thank you! I set the settings to what you recommended, can you send me the test model please ?

https://cults3d.com/:3308842

I suggest settings. They work for me. But as I said, it depends on the printer. How strong the part cooling is, which PLA is used, etc. One has to determine it individually every time. I always use layer height + 0.08mm for the Z distance on top of the supports, for example. That works quite well for me. I would recommend setting the part cooling to 100% and printing at 195°C. Layer height 0.16mm, Z distance on top and bottom 0.24mm. Keep in mind that the supports must hold very well at the pony's head and hooves so that they do not detach. (That's why the low speed as well). I set the supports manually and quite generously. I also use a brim around the supports, especially with tree support. For removing the supports, I used a small side cutter and a flathead screwdriver. The removal took about 1.5 hours.

Brim: 15mm

Layerheight: 0,16mm

First Layer: 0,3mm

Walls: 3

PLA: 190 - 195°C (190 when your part cooling fan is a small one)

Part-cooling: 100%

Support: Tree

max. Tree angle: 40°

z-distance support top: 0,24
z-distance support bottom: 0,24
interface layers: 2

Print speed:
outer wall: 45 mm/s
inner wall: 60mm/s
support 30mm/s

Please try these out first on the test piece. The supports should not come off too easily. Better to be a little tighter than too loose. If they are too tight, please increase the Z-distance; if they are too loose, decrease the Z-distance. You can also play a little with the temperature. If the supports hold too tightly: reduce the temperature. If the supports hold too weakly: increase the temperature.
Hope I could help you

Hi. Sry, what do you mean???

Mi tapón para la válvula mide 11 milímetros de diámetro

The valve cap screwdriver is for conical valve caps with a maximum diameter of 9.5mm

ohhh que pena!!! Gracias de todos modos

DANKE :)

Bitte schön ;o)

Hi mp_design,

Danke für die vielen LIKES die ich als Support von dir erhalten habe.😉
Ich habe mich entschieden die Kollektion mit meinen Dekorationselementen meinen Followern frei zugänglich zu machen.

COLLECTION: https://cults3d.com/de/drucklisten/AC-Design/dekoration-geschenke
CODE: FOLLOWERS-ONLY

Du kannst also alle Elemente gratis runter laden wenn du möchtest 😉👍

Schöne Grüße
AC

Danke mp_design 👍💛😉

Danke 💛👍😃

Hallo und danke für den Download :) Kann leider nur die STL Dateien anbieten. Beachte, dass das Riementriebgehäuse passend zu dem gewünschten Fräserdurchmesser / Lager gedruckt werden muss :)

Schade, selbst wenn ich das richtige Gehäuse drucke fallen die Lager von alleine raus.

Hab die Riementriebteile bearbeitet und zusätzlich eingefügt. Die Lagersitze haben jetzt exakt die Maße der Lager. D.h. die Lager können jetzt nicht mehr zu locker sitzen - tendenziell es jetzt notwendig sein, den Sitz vorsichtig einzuschleifen und dann das Lager einzupressen. Alternativ könnte auch ein Lager geopfert werden, das erhitzt werden und zum Einschmelzen verwendet werden. Danach die intakten Lager einsetzen. Diese Methode ist aber nicht erprobt. Ich hoffe, das konnte das Problem beheben.

Danke, jetzt passt alles

Hello, thanks for the download :) I'm adding the base for the pony

Hello, I assume that you are using PLA? For this model, I am using the lower temperature limit for printing (190°C). The printing speed should not exceed 50mm/s - even for the supports. As can be seen in the images, tree support is recommended. X/Y distance is set to 150%. The Z distance at the bottom is the layer height plus 0.08mm (I have had good experiences with this). The Z distance at the top can be set to the layer height, or, if the layer height is very low, increased to layer height plus 0.08mm. There must be no supports within the Voronoi structure (with FDM processes), as can be seen in the image. Larger overhangs must be supported outwards. This means that auto-support in the slicer does not work here. Please ensure that there is always sufficient cooling from the component cooler. Overhangs must not bend upwards (component cooling for overhangs at 100%, speed for bridges 25mm/s). A Z-Hop is also recommended. Removing the support structure under the legs and stomach is a little fiddly. It took me over an hour to remove the support. I hope I was able to help you a little. If you have any further questions, please don't hesitate to contact me :)

Printed with 5% infill, 3 wall line count and 0.28mm per layer

Hi, thank you for downloading it. The parts are designed so that 0.2 to 0.3mm tolerance is possible. I can offer the free calibration part to check the dimensional accuracy of the printer with a caliper. Most of the time it is due to the "Flow" setting. If the problem persists after calibration, please let me know and I will create a compensation module with more tolerance, exclusively for you. You would have to tell me the dimensions of your printed part so that I can create the part correctly for your tolerance. Until then, the link to the calibration cube: https://cults3d.com/en/3d-model/tool/calibration-cube-mp_design

and don't print this File too fast. I recommend 60mm/s. The slider of the compensation module is high. It is important not to let the part wobble due to too high a speed and thus lose the dimensional accuracy.

Hi, thanks for your quick response!! The printer has been calibrated before printing the pieces, maybe I didn't do it properly or because I am not an expert in the subject (Im not aware about flow setting for example).
What I forgot to tell that I printed with 130mm/s so probably that was the issue.
As a workaround I was able to attach the modules by using some little wires (the ones that are being used for closing supermarket bread bags).

Hello, can you please tell me the exact file you are having a problem with?
What material do they use?
Basically, the first layer must be applied slowly at a higher temperature without a component fan and at an optimal distance from the print bed.
I use an FR4 print bed that is degreased. To increase adhesion I use regular hair lacquer.
The files should be placed on the print bed so that the "B" (bed side) is facing down (onto the print bed). The files are tested. So far no error has been identified. If you have any further questions, please feel free to contact me :)

Hi, I'll take a look. If it's possible, I'll upload it as an update. A notification will follow. Thank you :)

Thank you so much. In the meantime, I will keep trying here also, as time allows. If i am successful I would be happy to post the mod also.

Es tut mir leid, dass ich erst jetzt die bevorzugte Sprache gelesen habe.
Ich bitte um Entschuldigung, ich hätte es besser wissen müssen :)

So. I modified the key fob.
The pony and frame are now separate.
The ground cannot be separated from the pony because it is necessary as support for the pony.
I uploaded the new files.

I would be very happy about makes and posts ;)
Best regards

Herzlichen Dank für die neue Version.
Ich bin in der Lage, die Teile zusammenzufügen und sie mit wenig Aufwand als Mehrfarbdruck zu drucken.
Jetzt muss ich es nur noch fertigstellen und das Ergebnis posten! :)
Nochmals vielen Dank

Hi, sry this model is not for commercial usage.

Hi. Thank you. I only uploaded it here. Unfortunately we have to wait until the cults team fixes the problem.

Hallo, das ist keine Schriftart. Wurde modelliert :)

Hallo, danke für die Anfrage. Sie sind nicht zufällig Leuchs Zündapp Dienst aus Hutthurm? Falls ja, würde ich mich im Laufe der Woche telefonisch bei Ihnen melden

Doch genau der. Wir sind ja einer der aktuell wenigen die die Lizenz der Verwaltungsgesellschaft mbH haben. Bitte per WhatsApp melden danke dir