Skip to content

OpenRC Tractor

Creation's quality: 5.0/5 (5 votes)
Evaluation of members on the printability, utility, level of detail, etc.

3D model description

There is a new version with improvements and more tools and addons that can be downloaded from my oficial site:

As an homage to my father and his first tractor I proudly present my next project, the OpenRC tractor. It's an open source 1/10 scale replica of an original Ebro 160D tractor. I designed it all from scratch and 3D printed all parts. Then, I added some electronics, nuts and bolts and I made it work!
I also prepared some basic instructions and BOM, so you can easily print and assemble your own tractor. It is designed to be easy to print and no supports are needed for any part.

Points to bear in mind:

As part of optional parts, you'll find different optional plates. There is one for Spain and one for Sweden because there are already OpenRC tractors in both countries. If you print your tractor and you would like to have a plate with your country letters, write a comment and I will try to add it.

Recommended motors have poor torque. They work on smooth surfaces but not off-road. I have prepared a mod to upgrade the tractor with a more powerful motor. Check updates.
I used same bearings as OpenRC formula1 to make it easier for those who already have the F1.
And you know what the best thing is? You can design your own tools!

With OpenRC tractor, possibilities are endless, new tools keep stay tuned!! (see below updates and get more details at (
Video in action

There is a lot of work put into this project, hope you like it and to see your prints soon!


Get the tractor trailer at:
Get the motor mod to use a standard 540 size motor at:


Get the tractor fertilizer at:

There is a new version with improvements and more tools and addons that can be downloaded from my oficial site:

Thanks to ZYYX 3D printer for sponsoring the project. OpenRC tractor project follows OpenRC by Daniel Noree's philosophy and it is licensed under CC-BY-SA 4.0.

3D printing settings

ZYYX+ 3D printer





Check BOM for details about printing settings and list of materials.

3D printer file information

  • 3D design format: STL and ZIP Folder details Close
    • 1-lower_chassis.stl
    • 10-escape.stl
    • 11-servo_arm_x3.stl
    • 12a-motor_right.stl
    • 12b-motor_left.stl
    • 13-rear_light_cover_x4.stl
    • 14-rear_arm_x2.stl
    • 15-rear_plate.stl
    • 16-rear_hook.stl
    • 17-front_chassis.stl
    • 18-front_badge.stl
    • 19-hood.stl
    • 2-upper_chassis.stl
    • 20-console.stl
    • 21-steering_wheel.stl
    • 22a-fender_right.stl
    • 22b-fender_left.stl
    • 23a-fender_arm_right.stl
    • 23b-fender_arm_left.stl
    • 24-seat_back.stl
    • 25-seat.stl
    • 26-front_rim.stl
    • 27-front_tire.stl
    • 28a-rear_tire_right.stl
    • 28b-rear_tire_left.stl
    • 29-rear_rim_x2.stl
    • 3-front_bridge.stl
    • 30-rear_axle_x2.stl
    • 31a-rear_axle_bracket_right.stl
    • 31b-rear_axle_bracket_left.stl
    • 32-rear_axle_lower_bracket.stl
    • 33-rear_arm_bracket_round_x2.stl
    • 34-alternative_rear_arm_bracket_hex_x2.stl
    • 35-rear_light_base_x4.stl
    • 36-alternative_rear_axle_x2.stl
    • 37-alternative_one_piece_rear_light_x4.stl
    • 38-front_light_bracket_V02.stl
    • 39-openRC_tractor_plate.stl
    • 4-front_dumper.stl
    • 40-center_rear_arm_holder.stl
    • 41-seat_base.stl
    • 42-steering_servo_holder.stl
    • 43-wheel_nut.stl
    • 5-front_axle_holder_x2.stl
    • 6a-front_axle_right.stl
    • 6b-front_axle_left.stl
    • 7-front_grid.stl
    • 8-front_dumper_block.stl
    • 9-160d_badge_x2.stl
    • optional_OT_Spain_plate.stl
    • optional_OT_Sweden_plate.stl
    • optional_OpenRC_tractor_plate_bigger.stl
    • optional_SE-3D_ZYYX_plate.stl
    • optional_ZYYX_logo_plate_big.stl
    • optional_blank_plate_to-paint.stl

    Learn more about the formats

  • Last update: 2020/04/04 at 16:06
  • Publication date: 2016/12/20 at 12:41





Issue with this design? Report a problem

Collection associated with this 3D model

Best sellers of the category Game

Add a comment


Tyres should be printed with flexible filament. They go in easily because they can flex a little.
It's better if you print last version of the tyres here:
There is a new version with improvements and more tools and addons that can be downloaded from my oficial site:

How do you get the rims inserted into the tires? I tried usingva mallet but thss as t smashed the rim. Thanjs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon or Aliexpress.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!