58 comments

Do you think this would work vertically? I've got a dry erase board I want to mount this on

Purchased your file for the 2d plotter but don’t see an stl for the plotter pen gear thanks!

Comprei o projeto e na hora que vou compilar o grbl da erro: erro compilando para a placa Arduino uno

Servodolfer for robot arm - I'm contacting you to ask about the SG90 Servodolfer. Do you have any files other than the mated files? Solidworks files other than the stl files

Hi I would like to purchase your hand writing machine 3d model. However, while inspecting I found that there is not design posted. Can you please elaborate all the design here is my What's app number. +8801848543185

Hi. I want to buy, but I live in Russia and card payment is not supported. Is it possible to purchase it in some other way?

hii. Is there a physical size for a 2D pen printer?

Hello,

Regarding V2 of the pen plotter. If I were to directly control the motors, do you have any information on the total area the pen can cover?

Thank you!

Hello, the servo that runs the z axis does not respond to commands... I believe there is a problem in the grbl file... can you help me?

Hello. I have a problem with payment. They don't accept my card.

hi,
how can i export these file into autocad

Hi ,
I had paid for a 3D file and have not received it yet ,below are the transaction details.
Please Help.
Thank you .
Payment from
A Khan
Date
29 March 2024

I am having a stepping problems, it takes HUGE steps when set the steps to 1 using UGS
the SG90 servo motor does not move the the pen up or down, it just flicks 1 mm left and right
I am using arduino uno and the cnc shield
arduino ide 2.3.2
What am I missing
Otherwise fantastic project, good fun so far

Still no answer from SuperBTech?

I will request a refund as author is a no show.

Hi,
Can please you provide me with the updated Grbl for the Pen Plotter 2.1.
I am having issues with the Y gantry, only 2 of the 4 wheels makes contact on the 2040 alu profile.
The eccentric nuts have been installed in 2 of the wheels.

Hello. I have bought the files to make the pen-plotter and I have some issues and I need your help. First issue is because of the servo, the servo doesn't work even when I put the maximum travel like S255. The servo moves only a little angle. Another issue is about the "square" because I start a draw and when the pen goes to other side of paper the pen is very down and almost rip the paper. Could you help me?

Hey! I'm having an issue with the pen plotter- everything is working as it should until i plug in the servo, then the board seems to disconnect from UGS following any sort of servo input, and i need to power cycle and reset.

is the power from the 5v pins on the cnc shield coming from the power supply to the cnc shield or the uno? I'm using 12v 6a for the shield and usb for the uno, but have also tried the uno with a 9v 1.3s power supply. not sure what the issue could be. have tried replacing uno, cnc shield, and servo with no luck.

thanks!

can You help me make pen plotter @drawing area 3000*3000 mm (normal speed and preciseness) .. on the end of X beam should have wheel.

I'm not experienced with internet, platforms, communities..etc.. so, please contact me on WhatsApp +306945032901

What's up my friend, I liked the first version of your drawing machine and that's the one I did, I have a problem, the servo does not work properly, it stays on when sending the command m03 s250, can you help me, please?

greeting,
I would like to buy this model. can it be printed on ender 3s1
how much plastic goes and are there any instructions on which screws and nuts go

Bro, Can you give me the modified version of grbl that you provide for DIY Pen Plotter, or even help me to how to edit it.

Bro, Please can you give me the modified version of grbl.

Please call me now +918871603141

ON STL files for V2 Plotter - what infill -- 30%, 40% ???

Hola
Si compro la version 2.1 puedo construir el plotter y el laser???