190 comments

Looking for a complete cab model, for the jeep comanche files.

hello my files are bad for the 78 ford can you contact me please

Hi,please respond on my messages on instagram because Toyota files are bad.Or send me fixed files on mail. dr650rs@yahoo.com

Can you email me
Jbpromogoods@gmail.com a out a 1970s ford body

IS THIS COMPATIBLE TO 1/10 SCALE RC'S?

I purchased your 1/24 bmw e30 touring files, and would like to know if its possible to make the body a little thicker? when i print it its very thin and breaks even when taking off the print bed or removing supports

Jeep Grand Cherokee ZJ with fenders (rc body 313mm wheelbase)

I purchased this model, but there are too many holes in the roof. Can you fix them and upload them again

Could you put the pieces onto a complete body shell version please to print whole, I've tried to assemble the parts afterwards and it doesn't go well. I don't need bumpers on just the body panels. I don't want to print as big as 10th scale regards Andy

How are you? Could you convert this body to 334mm Jeep Gladiator 62 (RC body)? It's not that complicated..? to acquire it.

How much for just body or shell of car I want to use for rc I can send you measurements of size. It’s a car from cartoon movie

Hey can I get this file fitted to a Mojave 4s.The ARRMA Mojave 4S desert truck body dimensions are: 24.5 x 12.75 x 3.5 inches. Specifically, the length is 24.9 inches (632 mm), the width is 12.75 inches (324 mm), and the height is 7.3 inches (185 mm), according to Pro-Line Racing. The wheelbase is 14.96 inches (380 mm

Just following up on my below comment, I am unable to print this shell due to there being holes in the RH front wing. Please can you rectify this?

https://i.imgur.com/V6JVnKS.png

Hi, I have recently purchased the Land Rover Discovery shell, and it has bad mesh quality. Please could you resend these fixed files via email? Thankyou. https://i.imgur.com/cDpt5EI.jpeg

hello, the left front side is not correct, cant print it without having problems, sliced on bambustudin and cura
can you check it?

Здравствуйте, https://cults3d.com/:1090567 а у данной модели длинна 448 мм, а ширина 194 мм?

Any chance of getting a 1992-96 Ford F150 Flareside body for a SCX24 frame?

Could you possibly resize your impala ss file to fit my Arrma Felony chassis (406mm)?

Здравствуйте, я б хотел у купить у вас 3d модель ниву пикап в 1:12 , колесная база ширина 150мм длина ~ 217мм

Hello, I’m looking at buying the ‘78 f350. I was curious what you’ve done or recommend for headlight/tail light lenses?

I have some question about the double cab dodge ram truck I have a makerbot sketch it has a 5.9"×cubed print area would it be big enough to print this ?

I have some question about the double cab dodge ram truck I have a makerbot sketch it has a 5.9"×cubed print area would it be big enough to print this ?

Hello. I was wondering if your 1/10 files can be turned into a one piece and scaled down to 133mm wheelbase and 155mm wheelbases

Hello, what scale is your Cadillac Escalade 2017 (RC BODY) file?

Thank you.

Hi, I bought your project Jeep Grand Cherokee ZJ. Unfortunately, the roof file has an error and cannot be printed (a gap in the model approximately 100 mm from the end of the roof). Could you please update the model and fix the file?

Hello, is it possible to make a 160mm wheel base Toyota Hilux design for a fms fcx 18