25 comments

Typically we buy sets of DIY earring kits, most craft stores or Amazon carry them :) then just glue the front of the earring onto the printed part

I'll add some instructions later, but any part labelled LH or RH with no matching side just needs to be mirrored

Should be fine!

Should be fine!

Heyo, you can message me on Discord @Juggerknob if you like. The button for the arduino is supposed to be tucked into the lower part of the handle in a small cavity, the button is then placed in, with a small panel glued over the top, so you never see the actual button, just the two bits labelled as such on the file :)

Thank you! In the end I figured it out and after putting some eva foam under the button so it would make contact with the outside part it worked out! I posted my make here on cults3d and on Instagram. Your files are really well made and I love how the sword came out!

It came through as an offer instead of a purchase? I accepted it.

Personally, scaling stuff is always a challenge. They are scaled to fit me (6'3) and my shins. If you take your height and work out roughly how much of a % you are shorter than that, reduce them roughly by that amount.

e.g. if you're 5'5 (165cm) thats roughly 13% smaller, so you could try that?

Alternatively. I find using a bit of software like Blender or Armoursmith to put a digital model of yourself, load the 3d model in and scale it on a digital model easier sometimes. Then just print it at the % you scaled the part to! Its been amazing for our workflow.

feel free to reply if you have any more questions. Cheers

I do not! apologies!

Hard to outline it here, but the concept is that there should be two LED strips running along the channels in the top of the rifle, under the coloured plastic, this needs to be wired into the section near the handle which has room for a battery and an arduino. Definitley print all the parts and tape them together to get an idea of where things go. You can also optionally put LED strips in the vents on the front, but its a LOT more work, you have to diffuse them, and wire up 8 individual strips, which where the wires run back through the empty channel through the centre of the rifle. Hope this helps, if not message me @JuggerKnob on discord

Hello again! I sent the request on discord. Do you have a tutorial for the general assembly and do i have to mirror some pieces?

Heyo, the storage is in the centre section, I use a power bank which is roughly 10cm x 6cm x1.5cm and it fits rather well. Personally, I'd get the blade/light sections printed and wired, then print the body and buy your power cell, as long as it fits and its 5v (normal phone bank) its fine :)

I assume your're the person from Instagram? I forgot to mention there, I sand/prime/paint all my props, nothing is perfect right off the printer :)

What designs did you want? I'm happy to just toss them up for a few bucks they aren't super hard to make

I looking for some blood angels stuff. Like a blood drop and something similar to their chapter marker

https://cults3d.com/en/3d-model/fashion/bloody-angels-wax-stamps hope this works

Looks incredible! Tysm!

Should be up now (or soon)

Looks great! are you planning to do the new Psylocke: Chouko Takahashi skin accessories and weapon?

I hadn't planned on it tbh, sorry. But I'm happy to chat about commissioning it? @JuggerKnob on discord

Weird, I've fixed and re-uploaded it. Thanks for the heads up

Heya! thanks for pulling the files, its saved a lot of time for Kayla's plushe production

Hi There, its a pretty common practise to not include parts which need to have a mirrored part included, since slicing software can easily just apply a flip onto the part, it saves on files size to not include additional parts which are the same but flipped. I would definitley recommend looking at your STL slicing software for the mirror option, as other designs on here likely have the same setup.

However, since this one runs on the smaller side, I've updated the file to include flipped ear cup and wings, you should be able to re-download it from your purchased tab on Cults.

I super appreciate the answer! I’m relatively new to printing my own stuff so I wasn’t aware of the need to mirror! Just confused on how I was supposed to put everything together once it was printed off. Thank you for the clarification, I’m excited to get it all put together!!

Apologies for that! I've fixed it now, you should be able to re-download it from the purchased Tab

much appreciated, downloaded the new version and all there. thanks again

Message me on Instagram @JuggerKnob, I don't usually, but happy to chat :)

Feel free to dm me on Insta @JuggerKnob, but they should print nicely on standard PLA or PLA+ with 15% infill, the shins are broken into four parts which will need to be joined.

Apologies, I seem to have scaled it up by 100% when exporting it, I've fixed it now, so if you either scale it down, or download the updated files :)

Thank you very much

Is about the dredd kit for space marine

I used them on standard firstborn space marine kits, but they should also fit with a little bit of scaling onto primaris scale

Do you mean the Mechanicus cog and skull logo?

I'll toss em up for a couple of bucks

Hey! Glad you liked the file :) Sadly, the shoulder is made out of EVA foam, with some freebie Eagle head and claw parts I found on here or Thingiverse. Sorry!

Good luck with the cosplay! I'd love to see some photos of it when its finished :D