8 comments

Just thanks for sharing !

I have the sound card without a case that uses the CM-108.
The old case that your design replaces does not hold the board.
Do you have a design that fits this case - https://www.amazon.com/MusRock-Drive-Free-External-Adapter-Required/dp/B0FTFSJ5JC/ref=sr_1_1?crid=6AZU12F3IWXD&dib=eyJ2IjoiMSJ9.ZrttttOAVqLlIIRmr5GwpSNrcTXqNtvK3xWMl3FwQAuU7pLo5CEj92Wd69ndlQDViMAgUp3amBe2z0_aQG7BYIr_esilQiNQREha_ytbUM-5VJQfJIaJI2PWkgpgHGDThHY1R5ViNd7fFOZcppR_k5AtcNTKkOoT7yXEw6duzV7CRKkUyaWKuuS799ALy3BalME0d16d_6HGanz_E43iJ4f9cZ_usLc2bbCPC80rof0DMlFvRvWWeWRr-JyiCQqhFTuCl3IqKx3UZ8-PfLr1Scfig2g1Pk0q8gkA8aaycek.n5bfgNAErKgriJA-eKxfzzDbTS7wCsliL5nRl1GLHMU&dib_tag=se&keywords=cm-108%2Busb%2Bsound%2Bdongle&qid=1779042513&s=electronics&sprefix=cm-108%2Busb%2Bsound%2Bdongle%2Celectronics%2C153&sr=1-1&th=1

hello how much does it cost to use your models for commercial use?

Hi, I'm trying to print the ruler but can't get the ruler lines to change depth. I have the my goal is to print the bottom layer in red then the rest in black. So the numbers and ruler lines are contrasted against the rest of the ruler. Can you help me get this fixed? I attached a picture of OpenSCAD and of it in my Creality Software. I'm trying to get the ruler lines to be red all the way up (for quarter inch, half inch etc) but if I go one layer futher it subtracts from the base of the measurement

https://ibb.co/SfPbDjQ
https://ibb.co/FzBryPL
https://ibb.co/9Z8s1Mw

i can't get the LT. side, Rt. side files to load into my printer. tells me no file found.

Hi I looking for a lamp screen in the same pattern as your vase, but I can’t see to modify your as I want, so I wonder if you can help me?
Hight 185mm
Top diameter 125mm
Bottom diameter 185mm
Best regards Micke

Hi, kurze Frage zu deinem NEFF DUNSTABZUGSHAUBE SCHALTER:
Für was sind die zwei unterschiedliche Versionen? Also was kann diese komplizierte, was das andere Modell nicht kann?
Bei uns ist der Schalter zum Einstellen der Dunstabzugshaubenstärke kaputt gegangen, welche Version brauch ich dann?

Vielen vielen Dank dir im Voraus!

Hello, sorry to bust in on your design here. i have recently bought a Qidi xMax2. It's I think my 11th printer and I believed and still do believe I'm ready for a large scale printer. i'm just having some issues. Basicallly, I've had it about a month and I haven't been able to put out a decent print yet. Usb was kaputz, fixed that, had leveling issues fixed that, now having slicer issues. Can you tell me if there are any blogs for this printer that I can plug into that you are aware of? Again, I do apologize for busting in on you. I'm really kinda lost. Amy