Zum Inhalt gehen

Lazy Cat

?
Qualität der Kreation: 5,0/5 (6 Stimmen)
Bewertung von Mitgliedern zu Druckbarkeit, Nützlichkeit, Detailgrad usw.
  • 👁 62,6k Aufrufs
  • 341 Likes
  • 1,5k herunterladens

Beschreibung des 3D-Modells

The laziest Articulated Cat!

**No supports required. Just slice and print!

After printing, just move carefully all the articulations to completely free them.

Check my other articulated designs here!

*Disclaimer: Not MMU/multicolor models. Pictures shown contain hand-painted models.


3D-Druckeinstellungen

A good first layer is mandatory for the print to succeed. Be sure your printer is calibrated and you have good bed adhesion.

Good layer cooling is also recommended, as it prevents curling and warping on overhangs.

https://www.youtube.com/watch?v=fBgikauUv1k

Informationen zur 3D-Druckerdatei

  • Format der Gestaltung 3D: STL Datei-Details Schließen
    • Lazy_Cat_v4.stl
    • Lazy_Cat_v4_tabs.stl

    Mehr zu den Formaten

  • Veröffentlichungsdatum: 2020/12/12 15:13

Copyright

©

Keywords

Creator

Seite mithilfe von automatischer Übersetzung übersetzt. Originalversion ansehen
Problem mit diesem Design? Ein Problem melden

Von der Community erstellte Kreationen

Bestseller der Kategorie Spiel


Kommentar hinzufügen

9 Kommentare

Out of curiosity, has anyone been able to print it successfully on the resin printer? I've made a few mistakes with mine:
a) printed at 50% scale
b) cured the print before freeing the joints by articulating them
Going to take another shot at it at 90% scale tomorrow (had a very hard time fitting it on Photon Mono), but this time, I'll wiggle it loose before the final curing step.

I did it at 50% scale, and it was very very delicate. As you said it is important to free the joints before curing. And also a thoroughly cleand with IPA to remove every bit of resin, especially from the leg joints (these are the most tricky). I use a cheap magnetic stirrer and works fine. Good luck!

I already did it the same as yours, I just wanted to see it, I also published it for free on thingiverse

  • 1 Like

That's weird... This one should be easier to print than the octopus. Be sure you are using the last version with tabs. If you have good bed adhesion the only remaining issue may be curling/warping due to poor layer cooling.
Hope this helps!

I keep having issues when I try to print this model. I have had good success with the octopus and elephant models. The issues I keep having are either layer shifts about halfway through the print, or one or more of the legs gets knocked loose during the print. I'm going to try again on a raft to see if I have better results. if you have any suggestions I would love to hear them. I verified that all of my belts are tight, so not sure why the layer shifts happen.

Far as I can see.log in to you account on cults ,select your account then go to orders.Your download link should be there.Hope that helps.

If you are not able to download them again you should reach Cults staff. I can't help there, sorry

my laptop crashed and i lost all my flexi models how do i get them again please.


Möchtest du Cults unterstützen?

Gefällt dir Cults und möchtest du uns dabei helfen,das Abenteuer in völliger Unabhängigkeit fortzusetzen? Beachte, dass wir ein kleines Team von 3 Personen sind und dass es daher sehr einfach ist, uns dabei zu unterstützen, weiterhin im Geschäft zu bleiben und zukünftige Entwicklungen zu schaffen. Hier sind vier Lösungen, die allen zugänglich sind:

  • WERBUNG: Deaktiviere deinen Adblocker und klicke auf unsere Werbebanner.

  • MITGLIEDSCHAFT: Führe deine Onlineeinkäufe durch, indem du auf hier auf die uns zugehörigen Links bei Amazon oder Aliexpress klickst.

  • SPENDE: Wenn du möchtest, hast du die Möglichkeit, uns hier über PayPal eine Spende zukommen zu lassen.

  • MUND-ZU-MUND-PROPAGANDA: Lade deine Freunde dazu ein, die Website und die großartigen 3D-Dateien kennenzulernen, die von der Community geteilt werden!