71 Kommentare

I’m sorry that you’re struggling to print.

The model has been rigorously tested to ensure it prints with the supports on various printers (I have tested on an old elegoo mars and a new Saturn) as unfortunately I can no longer provide unsupported models as they were being resold without permission.

I can only suggest that you adjust your settings to accommodate the extremely small supports, they do work but they’re designed to be small to retain detail. If you try settings more similar to those I suggest on the page they may print better.

Tengo la impresora perfectamente configurada, una Anycubic Photon M3. Me saca todos los soportes por finos que sean de sus piezas salvo unos pocos en el borde de esas piezas pequeñas, con lo que no termina de imprimir bien la pieza, el resto sale perfecto. He hecho 4 imoresiones y me ha pasado lo mismo en todas ellas en el mismo sitio. Si me dice donde hacerlo puedo enviarle fotografias.

My printer, an Anycubic Photon M3, is perfectly configured. It prints all the supports, no matter how thin, except for a few on the edges of the smaller parts, which means the print doesn't finish properly. The rest comes out perfectly. I've done four prints, and the same thing has happened in the same spot every time. If you tell me where to do it, I can send you photos.

I apologise, for me they print fine as long as settings are dialed in well and I've used the convoy lights on a couple of models you can see them printed on my 'E-5' rutscher listing as well. You mean the supports under the convoy light tube or the supports under the small circular tiger 1 reflector?

I'll upload the small tiger 1 reflector without supports for you

Muchas gracias. Ese es el que no me sale en el extremo inferior. El resto sale todo bien

Hi, I’m sorry you’re having that issue. If the buckets are printing fine and the supports work for the print etc. and the print only breaks up when you are removing it from the bed then the issue is not the raft and supports itself rather your initial burn in times/ first layers are too long of a UV exposure, meaning that the print is adhered too strongly to the bed (which can cause other issues and potentially damage your printer).

I do not generally supply unsupported models due to people breaching copyright, so; if you could please try first by adjusting your times, which would seem to be the issue, that would be the best resolution.

Ок. Я переделал эти модели,иначе их нельзяя правильно напечатать

Hi, glad you’ve got your settings fixed enough to print. As you can see by the product listing they do print very well, all of my prints are test printed on both old and new machines to ensure printability. I strongly recommend that you ensure your exposure times are not damaging your printer.

Hi, I took them down because people were having too many issues trying to print them. You’re interested in a 1/35 mp40?

yes sir

I’ll see if I can make it public for you but please be aware it’s a difficult print

can you support them and what price for vms debonder bottle holder

I did support them initially but they’re from years ago, nothing like the quality of my current lineup unfortunately and the debonder is a free model but please feel free to give what you can / think is fair. I believe the mp40s are visible again

thank you buddy

No problem, thank you for your business and please let me know how you get on with printing them

yes sir will do. how come you changed your name?

Just better branding really

and i think ill be alright with the printing cause i believe i finally got my printer dialed in on the money

qeustion buddy, so the mp40 printed fine. other than the butt stock didnt print corectly. i got a pic of my settings do i need to up times?

here are my settings
https://ibb.co/gbyPtD2C

Hi, I model pretty much everything at 1:1 or draw it at 1:1 for 1/35, if that makes sense, so they would retain detail scaled up to 1/16 (I obviously can’t say for sure how well they would print at 1/16 because of density when printing etc.) I’m sorry to not be of much help there but I can’t say for sure if they will or they won’t unfortunately. I hope you understand.

I checked and the file linked to that product is a sheet of the two types of bucket pre supported, the same as the product image. If a different file is downloading I will need to get on to cults3D as that is an issue on their end. Please let me know what is downloaded so I can fix this for you. Apologies for the issue and thank you for letting me know about it

Hi ya the 1st file was two pales one empty and one with water, just tried again and this time got the correct file, no need to refund ta

Apologies for that, the civilian hat is designed to be resin printed at 1/35 scale. It will likely never slice for FDM printing. I will refund you now.

¿No lo podrías corregir para que sea válido para FDM? Es una pena! :( sino es posible quedo a la espera del reembolso. Gracias.

I’m sorry to hear that you’re struggling with this, it would be interesting to know which slicer you are using; as I have printed them several times successfully. I will refund your purchase.

I am using AC DLP D2, and the resin used is official resin with no problem with the parameters. The inner wall of the model is very thin, and whether it is 1:35 or 1:72, it cannot be printed successfully. I used different supports and angles, but unfortunately it still failed, which means I cannot continue to purchase your other files,

Sorry about this, I have refunded you. However, the model does print fine as can be seen by the images on the listing.

If it's at a scale, is it possible to adjust the program to make it full size?

All of my designs are at 1/35 scale for scale modelling, simply multiply a dimension inside your slicer by 35x to achieve 1:1.

Sorry I’m extremely busy at the moment, so I have refunded the M1 helmet. I hope a redownload gets it working though. Apologies

Hi, sorry about that. What software are you slicing in?

Lychee pro

A few people have had issues using my models in lychee; I think it may be because the supports have been created in chitubox and lychee doesn’t like that. Is the issue only with the pre supported version?

I haven't tried it any other way other than with pre supports. I'll give it a go tomorrow and get back to you with my information

Sorry these are very small models designed for resin printing. The type of printer you have will not be able to print that small

Oh okay thank you. What resin printer would you recommend? Something I've always wanted to as well

I have an elegoo mars 2, it’s a bit outdated now but they have some newer models with higher resolution screens. Don’t forget that you’ll need to have a way of washing/ curing the prints too. Hope that helps

Sorry that you are struggling with that, I have successfully printed the pps 43 and must admit that the walls are very delicate on the barrel shroud as it is printed scaled exactly, poor printing design on my part. Unfortunately I believe that I no longer have the ability to edit the model (computer issues) but I will look into it for you. Might I suggest in the meantime printing it with both over and under exposure which may rectify the fragility. Apologies once again

I can try and do that for you, is there a specific orientation that you would like the mp40 printed in. It may take me a while to get round to as I have uni work to do. I could directly send you my original file if maybe the upload has corrupted?

Thanks for your fast answer.
Yes, we can try it with your original file again. How do you like to send it to me?

When do i get the original file?

I have uploaded a replacement file for you, it opens in my chitubox and previews for print etc. unfortunately Cults will not allow me to refund you as the payment is no longer pending, however, if you email me (only so that the code is individual) I can I think set up a discount code for a few items like ammo boxes (which I know are definitely flawless as they are drawn in a different program, so there won't be any printing issues :))

Hi, I’ve printed this with no issues before using the parameters that are listed, maybe the file has become corrupted I can send it to you if you would like. I’m very sorry about this but unfortunately I can’t test print it or redesign etc, as I am at university.

Well, ARAGON4, the simplest way of scaling would be to take the dimension of the holster in your slicer (for example 10) and multiply that by 35 to get a 1:1 model ‘length’ we then divide that length (350) by your desired scale (8) to get the length in appropriate scale (44 for the original 10)