Ir al contenido

Señuelo de la pesca de Crankbait

Descargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthoneDescargar STL gratis Señuelo de la pesca de Crankbait, sthone

¿Usted imprimió 3D este modelo?

Descripción del modelo 3D

This is my first go at designing a full size printed Crankbait. I think the finished model and results (fish caught) where well worth the effort.

The bait is printed in two halves and then glued together. (I used super glue) Three small pieces of 1.75mm filament are use to aid in aligning the halves while joining. A single piece of wire (I used motorcycle safety wire) is bent (see pictures for shape) to form the loops for tie on and the hook mounts and fits in between the halves before gluing together.

I printed this one with a .25 nozzle and .10 layer height to keep things smooth so your results may vary. After gluing the halves together the only post processing I did was to sand the glue seams flush.

The lure was airbrushed following the YouTube tutorials by "Lure Me In Custom Painted Crankbaits". I highly recommend them as they are easy to follow. I tried to seal the lure with Miniwax spray on polyurethane but a two part clear epoxy would probably be better/stronger. The lure floated in the beginning of the day but but the end it was sinking which leads me to believe it's not waterproof with the polyurethane. (it was also easy to scratch.)

I went back and coated these with EnviroTex Lite Pour-On High Gloss Finish epoxy and it really brought the colors to life.

Some initial tuning my be needed if lure doesn't run true. (Just bend the front loop the opposite way it runs.) Running depth is about 6-8' depending on retrieve speed. A rattle effect can be added by dropping a few BB's or bearings in the float chamber. (See Picture)

8-25-16 = Replaced the Stencil for airbrushing stripes with a better version, although this version does require supports it is a lot easier to airbrush with. It's not a perfect fit but it works well enough.

If you make one of these and actually catch something post your catch in the Makes.

Parámetros de impresión 3D

Printer Brand:
MakerGear

Printer:
M2

Rafts:
No

Supports:
No

Resolution:
.10

Infill:
90%

Notes:
I used 90% fill but as long as you're coating them with epoxy you could probably get away with much less infill. I've since done a few smaller ones at 20% to keep them light.

I printed the Stencil with a .20 layer height.

Videos: https://www.youtube.com/watch?v=wssPKoW5VRo & https://www.youtube.com/watch?v=WrbgoCUbPLQ

  • Formato de modelo 3D : STL

Palabras-clave

Creador

Licencia

CC BY NC

Página traducida por traducción automática. Sugerir una mejor traducción

Modelos 3D similares

Los más vendidos de la categoría Variado

Contenidos correspondientes


Añadir un comentario


¿Te gustaría apoyar Cults?

¿Te gustan Cults y quieres ayudarnos a continuar la aventura de forma independiente? Tenga en cuenta que somos un equipo pequeño de 3 personas, por lo que es muy sencillo apoyarnos para mantener la actividad y crear futuros desarrollos. Aquí hay 4 soluciones accesibles para todos:

  • PUBLICIDAD: Deshabilite su bloque de anuncios AdBlock y haga clic en nuestros banners.

  • AFILIACIÓN: Haga sus compras en línea haciendo clic en nuestros enlaces de afiliados aquí Amazon, Gearbest, Banggood, Aliexpress o Ebay.

  • DONACIÓN: Si lo desea, puede hacer una donación a través de PayPal aquí.

  • PALABRA DE BOCA: Invita a tus amigos a venir, descubre la plataforma y los magníficos archivos 3D compartidos por la comunidad!