Pular para o conteúdo

Esqueleto louco

gif-1-cults.gif Esqueleto louco
1.jpg Esqueleto louco
gif-2-cults.gif Esqueleto louco
gif-3-cults.gif Esqueleto louco
2.jpg Esqueleto louco
3.jpg Esqueleto louco
4.jpg Esqueleto louco
5.jpg Esqueleto louco
gif-1-cults.gif Esqueleto louco
1.jpg Esqueleto louco
gif-2-cults.gif Esqueleto louco
gif-3-cults.gif Esqueleto louco
2.jpg Esqueleto louco
3.jpg Esqueleto louco
4.jpg Esqueleto louco
5.jpg Esqueleto louco
Faça uma oferta
Compartilhar
Adicionar a
Make
?
Qualidade da criação: 4,8/5 (59 votos)
Avaliação dos membros quanto a adequação para impressão, utilidade, nível de detalhe, etc.
🏆 Melhor ?
Licença
Formato do design 3D
1 arquivo (ZIP) Fechar
  • Creazy skeleton By Dancing Toys..zip
    • Assembly Tutorial.mp4
    • Body.stl
    • Engine Set.stl
    • Extremities Set.stl
    • Head.stl
    • LICENSE.txt
    • Movement Set.stl
    • Single Pieces/Arm Shaft.stl
    • Single Pieces/Body.stl
    • Single Pieces/Cap Screw.stl
    • Single Pieces/chest.stl
    • Single Pieces/Criquet.stl
    • Single Pieces/Escape.stl
    • Single Pieces/Gear 1.stl
    • Single Pieces/Gear 2.stl
    • Single Pieces/Gear 3.stl
    • Single Pieces/Head.stl
    • Single Pieces/knob.stl
    • Single Pieces/Left Arm.stl
    • Single Pieces/Left Leg.stl
    • Single Pieces/Movement Structure.stl
    • Single Pieces/Offset Axis.stl
    • Single Pieces/Right Arm.stl
    • Single Pieces/Right Leg.stl
    • Single Pieces/Spring to Windup.stl
    • Read me print parameters.pdf

Saiba mais sobre os formatos
Última atualização
Data de publicação
Número do design 1523892
Autor do design DancingToys
DancingToys

DancingToys

Conta certificada
Algum problema com este design? Relatar um problema.

20 comentários

Adicionar um comentário

👉 Faça login para escrever uma mensagem

20 comentários

nonibearno
nonibearno

Guess I should have read the comments first. Gears are not working as seen in the video. Recommended fix is to print gears using PETG, not PLA. Or add a washer to the axels.
Tatycgc
Tatycgc

gastei dinheiro a toa, absurdo vender isso, engrenagem nao funciona, a cabeça é muito grande entao não gira ou trava, as pernas abrem demais, uma porcari4.
diastazzz
diastazzz

its work correct?
hunterfruff
hunterfruff

sense the creator of the print wont answer!

i put wheel bearing grease on all the gears especially the timing gear that looks like a wish bone, it was causing a lot of friction on the main gear.
twafagaraz
twafagaraz

O preenchimento não é 10%! ficou ruim... algo deu errado. tive que preencher com cola.
The filling isn't 10%! It's bad... something went wrong. I had to fill it with glue.
WillL84
WillL84

What does it mean in the print info where it says "wall thickness 1.32"?
skeeproductions
skeeproductions

Hi! Does it work to scale it down?
nccortesegravacoes
nccortesegravacoes

o meu nao funcionou, ele da corda e trava
DaneM
DaneM

Hi I’m having trouble with the assembly. Is the gear suppose to snap into the round loopy twirl bit? Because these pieces aren’t connecting.

LJTT3DPRINTING
LJTT3DPRINTING

hi there

I have purchased this file and have printed 2 and they do not work twist the key and it goes to move then gets stuck

is there a way we could fix it to make it work

aaemuller
aaemuller

Did you find a fix to this? I'm having the same issue

LJTT3DPRINTING
LJTT3DPRINTING

no i have not fixed it lol

hunterfruff
hunterfruff

sense the creator of the print wont answer!

i put wheel bearing grease on all the gears especially the timing gear that looks like a wish bone, it was causing a lot of friction on the main gear.
bairdsnest
bairdsnest

i have made 2 of these. 1 in a glow pla and another in bone., glow is rough, bone is super smooth. both of them are sticking when the circle inside the oval channel is in the upper left side as your looking at the skeleton. what would the issue be? i made this as a prototype to sell it and it would be a shame if i cant get it to work. i have about 40 different people wanting to buy one.
Mishti3D
Mishti3D

?
Mishti3D
Mishti3D

Hi, we are having a problem with weak links in this model. Specifically, the elbow links and where the hands hold the head. The lower parts of the arms are very thin and the elbow links are very weak, so the head keeps flying off after it starts doing the dance. Sometimes even just standing up in place. The hands also easily detach from the head when it's wobbled even a little. Is it possible to get a refund? I can provide a video.

thomasthiaudiere03
thomasthiaudiere03

you are soooooo stingy! lol

  • 1 curtida
PRINTITO3D
PRINTITO3D

Nice job 👍👍
neiloler
neiloler

I printed this, loved the video and it lives up to the hype.

Have you thought about putting a small motor and battery in it?

  • 1 curtida
3DPrints747
3DPrints747

This skeleton is awesome and highly recommended! I did a quick video on my Youtube channel to promote it because I thought it was so cool. Easy, quick print.

https://youtu.be/bTeNcewczJQ

  • 3 curtidas
DancingToys
DancingToys

I'm glad you liked it! And thank you for the video. If you could add it to "make," it would help me a lot. 😄

  • 2 curtidas
Pierre
Pierre

Heads up!!

  • 1 curtida
DancingToys
DancingToys

🙌🙌 yep hahaha

DancingToys
DancingToys

🤩😃
arqmlizio3
arqmlizio3

hahaha I love the new dance :D

  • 2 curtidas
DancingToys
DancingToys

Thanks :D
Hugo
Hugo

Very funny ;)

  • 2 curtidas
DancingToys
DancingToys

Hahaha thanks

Quer apoiar a Cults?

Gosta da Cults e quer nos ajudar a continuar esta aventura de forma independente? Nós somos uma pequena equipe de 4 pessoas, por isso é muito fácil nos apoiar para continuarmos em atividade e criarmos novidades para o futuro. Aqui estão 3 opções acessíveis a todos:

  • ANÚNCIOS: Desative o bloqueador de anúncios.
  • DOAÇÃO: Fazer uma doação via Ko-Fi Doar
  • BOCA A BOCA: Convide os seus amigos para acessar e descobrir a plataforma e os arquivos 3D incríveis compartilhados pela comunidade!

Compartilhar e baixar arquivos na Cults3D garante que os designs continuem nas mãos da comunidade maker, e não nas mãos de grandes empresas de impressão ou software 3D, donos das plataformas concorrentes, que exploram os designs para seus próprios interesses comerciais.

A Cults3D um site independente e de financiamento próprio que não precisa prestar contas para nenhum investidor ou marca. Quase toda a receita do site volta para os makers da plataforma. O conteúdo publicado no site atende apenas aos interesses dos próprios criadores, e não aos das marcas de impressoras 3D que também querem controlar o mercado de modelagem 3D.