63件のコメント

When you purchase or download my models, you can use them however you like, including selling what you print yourself.

I just have one request: it would be great if you included a link to my models in the product descriptions.

??

Etheral change pose? And other tau minis?

write your wishes

Can we talk on Instagram or something? My Instagram is: TauFarsight

And speak good!!

You can write to me by email: hellgerjohn4@gmail.com

If you only distribute files that have geometry changes, then yes, you can.
I'd be interested to see what you come up with. :)

Please clarify the issue. Does the weapon model in the archive significantly differ in size from the original model?

There’s no issue, just a request for an update to the kit, the bigger submunitions rifle is for R’alai, but in the old Imperial Armour books there were rules for non-experimental pulse submunitions rifles for Hazards and I would like some that could be magnetized on the same mount as the other main guns

Please clarify which set this model is from. If you're referring to the miniatures in the Hello Kitty Marine photos, they were created using original plastic models and a 3D-printed upgrade pack.

thanks for the response, i mean the fish ones

Where did you see a "gavtank turret" among my works?

Hi. It was so long ago that I forgot, and you're the first person to ask this question in years.
I've corrected the file; it should be clearer now. You need to download the archive again.
You need to print files from the "Support" folder, you shouldn't need files from the "SP" folder.
It is important to note that the attached files with supports may not be suitable for your printer or resin, if the printing is unsuccessful, I can only recommend making the supports and hollow parts yourself.

Unfortunately, I can't guarantee 100% compatibility.
However, the shoulder joint, which attaches magnetically to the torso, is fairly similar to the original.
If the magnet attachment points don't match, you can enlarge the holes in the torso or file down the protrusions near the joint and glue the magnets on top.
If you are very worried that something will not fit, you can measure the diameter of the holes, their depth and the distance between the holes in the case and write to me.

Hole diameter is 8mm for the two that are in line with each other. Couldn't get measured from the centre but from the top most point of the top hole to the bottom most point of the bottom hole is 26mm so I'd estimate the distance between centres is 18mm. Deepest point of both holes is 5mm. Depth to the kinda step thing in the hole is 3mm

https://cults3d.com/ru/3d-model/igra/kx139_shoulder-joint-fw-388236c1378d36751f72
I took into account the dimensions you indicated and made changes to the hinge, try printing it and fitting it to your body.

I'm getting a 404 whenever I try to use the link :(

https://cults3d.com/ru/3d-model/igra/kx139_shoulder-joint-fw-5fe2c416ad133493cc17

That works. Thanks very much

Thank you for your support. I really like the original Ethereals, and I hope I haven't ruined them too much with my edits. I'll try to finish the entire Ethereal line. If I can get my hands on some miniatures or scans, I'll make miniatures of the Air and Water castes.

Ruin? Your edits were very tasteful, I bought the Ethereal with dual Equalizers and I am using him on a hover drone to stand in for the newer Ethereal, the staff looks awesome on that model, and the honor blade Ethereal looks really good, I am really happy with your work. Thank you again.

I'm currently doing the standing version, I think I'll finish it in a couple of days, after that I'll do the sitting version.

Ok

Thank you for your donation. If you have any questions or suggestions, please leave them here.

I was wanting to reach out about the A tuna - but the interest was more of a private one.
https://discord.com/users/iiohab

Look at this author
https://cults3d.com/en/3d-model/art/my-panic-suit-supported
His models are very accurate in replicating the original Tau design, feel free to use his models.
Due to copyright issues, the author was forced to remove the preview, but the appearance of his models can be found on the Internet.
At the moment, I do not plan to make models for Tau, which already have very good 3D duplicates from other authors.

Thank you for the link and the swift response, I just finished exporting your drones and look forward to printing, thanks again.

I haven't done much modeling or Warhammer in general in the past year, for many different reasons.
Today I saw new work from XenoBits, these were ethereal, his work is quite good and you can see the similarity with the original resin models, however, I think that some details are missing.
And so I finally sat down to make my version, at least one of the ethereal is worth waiting for this week.

The big problem is the face, the resin models have very different designs and are not very detailed, the current plastic ethereal models look too young. It is difficult to find a reference and make the face charismatic enough.

Previously, there were no complaints and the models were printed on different FDM and SLA printers, perhaps the features of the important slicer. Yes, there may be errors in small details in the models, but this should not lead to problems with printing and they can be ignored.
I tried to correct the files you specified, download them again.
Perhaps your slicer has automatic error correction tools, use it in case of problems with printing.

Downloaded the new ones and they all work now, thank you so much for the fast help!

Sorry, I can't provide you with these files. Also note that hollow files are made after the supports are installed, this is due to the fact that the program starts installing supports inside the parts.
I can provide you with the settings for hollow parts from ANYCUBIC PHOTON WORKSHOP.
Wall Thickness 1.3mm, Accuracy 1mm, Infill Structure: BCC, Sell Size 13mm, Strucrure Radius 1.2mm. For small parts: Infill Structure: None.

aaaah, I see. That's okay. Thank you

Personally, I used the original plastic fire warriors. If you don't want a complicated conversion, then you can put a fire warrior aiming a pistol next to the sighting device, or use a sitting position, but then you'll have to change the position of the original hands. You can also watch videos from the game Tacticus, where a marksman is shown using the sighting device while running.

Fair enough, thanks ario

The parts for the right and left legs are the same, select the desired part options and mirror them in the slicer.

Ah, that's perfect. Thank you! I feel so silly

Don't worry, all the parts can be printed even on the smallest printer, but keep in mind that files with supports are not always suitable for all resins and printers, so I recommend testing the print on small parts, and then printing large ones.

Great thanks for clarifying, I will keep that advice in mind