Mano Flexi PRINT-IN-PLACE

Printed it on a Bambulab A1 with White PLA Matte, 0.4mm nozzle, 0.2mm layer size. I scaled it down to 80% and was prepared for having to "crack" some of the knuckles, but it worked flawlessly. I have a feeling it could be scaled down to 50% with a 0.2mm nozzle and 0.1mm layer size.

I did have some adhesion issues on the first run (though that is not a problem with the model, but with printing large areas in general), so I slowed down the first layer to 20mm/s. It worked perfectly then.

Really great work, nice attention to detail! It's one of those models that is actually fun to watch while it's being printed.

I would love to scale these down.. has anyone had any issues doing so and still maintaining the flexi movement

Fun result. Very realistic

Great print as usual from flexifactory
Printed with no problems iv never had any issues with your prints

It is not suitable for printing small. The rings are designed very thinly

hi! is this prosthetic capable of fully grasping a cylindrical protrusion approximately 2 inches in diameter with a circumference of 4 inches. it gets a little wider near the top of the cylinder. also, would you say the filament you used is "soft to the touch"? thanks its big help getting feedback before making a BIG print if you know what I mean ;)

hello je voudrais acheter deux mains une droite et une gauche

This looks like the thing, in Wednesday.
Great Design!

Just wowed away by your designs and about to buy some of them for printing. Just an additional idea for the flexi hand. Add a bit of forearm to get something like a fly swatter. And for the hand movement, if it's laying down it looks like a fist. When you raise it, then it (depending on the model) either raises just the index finger or the middle finger. Would be for sure a lot of fun for office use. :)

can this be used on a resin SLA printer?

Printed it at 80% on a CR-6 and it worked perfectly. I was a little late switching to the white for the bone, but my kids love it. Am currently printing it at 120% to match my kids handsize in a more flesh colored PLA. But i am going to give it a try with some TPU that is flesh colored, I might carve out the bone and leave a hole with meshmixer so i can add the white bone in PLA later for maximum creepiness. Wonderful model. The fingers move just enough to lay naturally when you walk up and put it on someones arm.

Hi there! is there a version without the bone sticking through? i wanted to print one for my nieghbor's kid and figured that i'd like to do it without a bone. Someone shared a version that you have on patreon that comes without the bone sticking out. could that be possibly offered here?
Thanks!

Hello. What is the recommended layer hight, 0.2 mm ? I didn't see it in the print parameters section. Thanks.

very realistic

Could be great, if bone can be printed separately

someone just stole your design and is selling it, just so u know.
https://cults3d.com/en/3d-model/game/mano-flexible

Ok well don't print this at 50%, the joints are so small and fragile, broke with a few wiggles. Also the color change thing was a joke. Tried it and the second color wouldn't stick to the first one. What did I do wrong? WIll not be printing this in multicolor unless I figure that out first.

Was wondering if I could print and sell these for Halloween, with design credit to you of course!

I've printed this 3 times on my MPSMv2 and the joints never hold together. It's at 85%. 50% infill. Not sure what to do.

Can this be printed with a resin printer?

hello, can it be scaled?

es tremendo lo bien que queda. con pla.. muy contento con el resultado. gracias

Hi, you need to make the links between the fingers stronger they broke very easily.

Hey Dan,

I love your models and am currently printing the Flexi Hand right now. I have printed a bunch of the Flexi Fish to decorate my tiki bar and will be adding the skeleton to the bar as well.

Is there a way to know when you are putting out new designs?

Thanks.

Can you please make some more,your flexi models are the best.

Nice job! Flexi factory is awesome

What filament skin use?

Absolutely love your stuff. Downloaded it's gonna be the 1st testprint on my new printer. Is there any chance you might be do an updated version with a little bit more zombified look to the hand for Halloween ?
Keep up the great work .

Printed and shared with the Creality CR-6 group. I love it.

Hi, is there still a way to get it for free? I saw the post a few hours ago that it would be free for two days and I wanted to download it now but it isnt available anymore and the post got the deleted.
I'm so sad rn because it would have perfect for my Halloween decor I thought I still had time to download it :(