24 commentarios

Hello! This was my very first model, I will download it, check it out and get back to you. Sorry its been along time since using this model!

Yeah it just loads a really long model. I dont know why. Is it supposed to load in pieces?

Hello, I just opened this model on my creality slicer and had no issues or bambu. Its a 3mf file so can be used for ams printing, have you tried importing as a 3mf generic on tablet and pc? I cant seem to find an issue my end, but i will upload the file to creality cloud if you have that slicer to use?

I can’t figure it out. It doesnt work on Bamboo slicer or Elegoo Slicer for me.

Hello! I am so sorry about that, I will upload it now for you. I'm not sure why it wasn't uploaded before!

Oh thats amazing! Well done 😍

Thanks for your appreciation

Hello! the room is a shell and the furniture peices are all seperate to print and place where you like. 😊

Hello! I'm sorry you are having trouble. Is it the seahorse flexi you are trying to open? It needs to be extracted as its in a zip folder, there are two files, one 3mf and one stl. What are you slicing it on?

Hello! When did you download the file? As when I first uploaded it, I uploaded the wrong door file then replaced with the correct cage door! Sorry about the muddle up 😅

Hello what model are you referring too please?

the Cage

What problems are you having and what are your print settings ?
as its most likely the settings and needing to calibrate your printers in ☺️

the bottom of the cage inside the pattern does not cover the entire bottom, also will def need supports as the top quality inside is not very smooth , and door . I am running Bambu P1S. Love the design !

The design is only ment to cover partially on the bottom that is part of the design ☺️ and the cage can be printed with no support as mentioned but will need some slight clean up but if you'd like a clean finish then support is recommended ☺️ thank you! X

ok Thanks for such a quick response!

You're very welcome ☺️x

Hello just added sorry about that! Mum brain today 😩

Hello! Giving the hinges a quick file down/ sand down will help them slot in.

You can also use wire or some filiment to hold the hinges in place. The cylinder has very small tolerances so any filiment in the hinge hole will stop it going in. I hope this helps. Let me know if you are still having issues x

Any luck or help needed? 😊

Okay I've double checked the cat and there are no layer holes, only gaps where the joints are needed but it's all jointed together. I have printed multiple tests out of these and am certain. But if you need any help figuring out your slicer let me know. Also possible try another slicer? Are you printing fmd or resin? This piece has been tested for fmd prints only. Hope this helps!

I have done a screen record layer by layer of the model on my slicer to show you there are no gaps in this model. I can message you the video if you would like. If you'd like any help trying to figure out why your slicing software is messing around I can try to help the best I can,but it definitely isn't the model at fault.

Hello! So I think you have my model confused with the articulated dragon model you brought. I checked on your profile and can see similar issues on the dragon file by multiple people!

Hello! Oh I think what you need to do is press scale on the side of the slicer software and scale it up by 1000 or something! (The model was designed in a sculpting program that doesn't have units so it can be really tiny on some slicers and needs making bigger ) he's there somewhere on your plate, hope that helps and thank you for downloading 😀

Hello! Sorry about that I will upload the other stl file for it. Not sure why it wouldn't work!

I've just realised you may need to scale him in slicer. If nothing appears when you open it, it's there but just really tiny as I created it in a software that doesn't use units of measure so needs scaling!

Hello! Sorry about that I will upload the other stl file for it. Not sure why it wouldn't work!

I've just realised you may need to scale him in slicer. If nothing appears when you open it, it's there but just really tiny as I created it in a software that doesn't use units of measure so needs scaling!

Hello you will need to scale up to about 3000% or enough to cover your build plate, the sculpt software I used doesn't work in measurements so you have to apply that in slicer 😄❤️