Aller au contenu

Attention les amis, il ne s'agit pas d'une messagerie privée mais bien d'un fil de discussion public. C'est un lieu d'échanges, merci de rester courtois et respectueux. Toutes sollicitations commerciales ou malveillantes sera supprimée. Si vous évoquez un design en particulier, n'hésitez pas à ajouter dans votre message le lien ou à donner le titre du modèle afin que la conversation puisse être correctement orientée. Si vous souhaitez joindre des photos au sein de votre message, n’hésitez pas à téléverser vos images sur un service d’hébergement d’images en ligne gratuit comme Imgbb et à copier / coller les liens de vos images dans votre commentaire. Bonne discussion !

Écrivez votre message :

14 commentaires

Hola buenas . Encontraste alguna solucion ?

hola, he subido una nueva versión hecha desde cero, espero que esta se adapte bien.

Hola, el modelo que baje no es el que se muestra en las fotos. Quiero el q esta en las fotos, si no no me sirve

Hola, me puedes enviar fotos de la funda puesta en el teléfono para ver qué es lo que falla o no encaja ? Gracias

Hola no es para mi , es para regalar, el celular dice Samsung abajo , y la foto que tenes tiene calado como para que se vea . Esa misma quiero

This case is NOT for the A53, but for the A52!
The A53 and the A52 are very much alike, but not the same. The knobs are on a slightly different place, a opening for the top/left loudspeaker is missing, the 3.5 mm jack is useless (the A53 has non) and the microphone is slightly off. Whit some extra cutting you can use this case on a A53, but it is not the perfect fit you would expect.

Hola, gracias por tu mensaje, intentaré corregir esto, podría subir alguna foto en imgbb.com?

On your "Case samsung galaxy s22 plus 6,6" design the outside of the upper corner where the camera cutout is doesn't extrude until the Z is at .6mm. It would sure help if it could extrude the outer edge at z=0 otherwise it risks getting pulled up during printing as it's not adhered to the bed. I'm trying once more (2 failed prints) with some different settings. If that doesn't work then I'll need to add support structure to it. But since I'm printing TPU those are a pain to remove. Just thought you'd want to know.

ok, thanks for your message, tomorrow I will check it.

I have uploaded version 3.4, I hope it is the final one, thank you very much :D

Love the V3.3. Just needs some slight adjustments. I have included some pics of the camera location and dimensions. Also, there is an issue with the transition from the base to the sides. Thanks for the updates. https://ibb.co/album/C5PHpb

  • 1 j’aime

Thank you, after seeing your photos I have made an adjustment again. V3.2

I have also uploaded version 3.3 with 1mm more height to better protect the screen

Thanks for the updates. I have provided some additional photos for the specific size dimensions of the hardware. I think that the holes for the stylus, USB C port, power, and volume keys need to be a bit larger. Also, the mic hole at the bottom should be closer to the USB C. One last thing, I added a screenshot of the height of the end at 9.0mm. Could you extend the top and bottom to this and leave the height of the sides as is? https://ibb.co/album/gz8Twn

  • 1 j’aime

I just uploaded one more photo of the end height at a total of 11mm. Please, let me know if you have any questions. Thanks.

Love the V3 version. However, there needs to be a lift to the power and volume buttons upward as well as larger holes for the stylus and USB C port. It would also be good if the top and bottom were extended to the edge of the phone. The height of the sides are great. Thanks. https://ibb.co/7QjhGtT https://ibb.co/SvPcVCT

  • 1 j’aime

Thank you very much for the photos, in a few hours I will correct it.

The V3.1 version is now available for download, corrected the alignment of the holes.

Is way to thin the case

hi the model i purchased for the s22 ultra case has the slot for the SPEN at the wrong side

  • 1 j’aime

Hello, thank you for your message, I will correct it in a few hours, sorry for the inconvenience.

  • 1 j’aime

hello, the design is already corrected and improved, if you have any other suggestion do not hesitate to contact us, thanks for your download

thank you for fixing that so quickly! are you able to make the sides of the case slightly thicker?

yes no problem, uploaded v3 version with 1.5mm wall thickness

Hello, do you have the 3D model just for the Center Cap?

Hola, respecto a que modelo?

For R5 alpine rims

He subido uno, espero que te valga

Bonjour, je suis vraiment novice dans l'impression 3D, quelle taille de plateau d'impression est nécessaire pour la prise d'air R5 ? est ce qu'un plateau de 300 * 300 * 400 est-il suffisant ? je vous remercie, Sébastien

si , es suficiente, si la pone en diagonal no tendras ningun problema

Hello,

Thanks for the clio 16V badge.
Do you have the Speedline Maracana center wheel cap?
e-mail me: nuno.oliveira.costa@hotmail.com

Thank you,
Nuno Costa

Hola, no tengo uno para tomar medidas