Aller au contenu

Mini bateau à réaction RC 200

?
Qualité de la création : 4,5/5 (31 votes)
Évaluation des membres sur l’imprimabilité, l'utilité, les détails, etc.
  • 98,4k vues
  • 227 j'aimes
  • 854 téléchargements

Description du modèle 3D

Bateau pleine grandeur avec stator et buse 230x75x50mm

Taille du bateau sans stator et buse 200x75x50mm

Vous avez besoin d'une imprimante 3D avec une hauteur d'impression minimale de 200 mm.

Suivez-nous sur Cults3d et sur Youtube pour être informé d'un nouveau téléchargement !

Les premiers téléchargements de chaque nouvel envoi sont gratuits.

Mini Jet Boat 200 Mono contrôlé par RC

Mini Jet Boat 200 Twin contrôlé par RC

Mini Jet Boat 300 Mono contrôlé par RC

Prenez ce modèle, si vous n'avez besoin que du Water Jet Drive

Pour les débutants, je recommande de commencer avec le RC Jet Boat 200 Mono ou le Jet Boat 300 Mono

Vidéo :

Liste partielle (dernière mise à jour le 2020.05.07)

Moteur sans balais

ou

Moteur à brosses

Mon contrôleur RC (exemple)

ou

Est-ce que c'est étanche ... OUI, c'est le cas !

  • Regardez la vidéo RC MiniMono Boat - Jet Drive imprimé en 3D sous l'eau Après cela, il n'y avait plus d'eau dedans !

  • Si votre empreinte de la coque est bonne, elle doit être étanche. Mais, si vous voulez être sûr, vous pouvez toujours la peindre avec une fine couche de vernis automobile. J'ai essayé les deux variantes et ça marche très bien.

  • L'arbre de transmission du bateau est scellé entre deux paliers lisses par un joint lubrifiant.

  • La couverture est scellée avec un cordon de 2 mm de caoutchouc mousse ou avec un sceau flex imprimé en 3d

Mise à jour

  • 20200827 a ajouté la décoration par autocollants en svg et pdf

  • 20200611 mise a jour de la liste des pieces d'esc et de moteur

  • 20200603 ajouté moteur_180_ adaptateur.stl

  • 20200527 a vérifié tous les liens

  • 20200324 Correction d'un bug dans les logiciels boat_hull_split_a et boat_hull_split_b

  • 20191027 mise à jour de boat_hull, nozzle, seal

  • 20191005 ajouté bateau_trimtabs

  • 20190924 a ajouté boat_cover pour Self-Righting

  • 20190907 nouveau VidéoTutoriel pour assembler l'électronique du Jet Boat

  • 20190815 couverture de bateau optimisée pour une impression 3d plus facile

  • 20190806 a ajouté une version boat_hull sans support de batterie 18650

  • 20190721 a ajouté une nouvelle couverture de bateau coordsys, certains trancheurs ont eu des problèmes

  • 20190712 a ajouté des photos de la mise en place et du montage de la cura

  • 20190708 travaille sur une vidéo et un tutoriel "How To

  • 20190702 a ajouté une coque de bateau divisée pour réduire la hauteur du volume de construction.

  • 20190701 téléchargement initial

Modèles 3D supplémentaires :

Object License - Licence standard de stockage de fichiers numériques

  • Remixage non autorisé

  • Utilisation commerciale non autorisée

  • Ajouter des crédits au concepteur lors du partage de liens, de photos et de vidéos d'objets

Montrez-moi vos marques.

Découvrez mes autres dessins jtronics sur cults3d


Site web : http://www.jtronics.de/

Instagram : https://www.instagram.com/jtronics.de/

Youtube : https://www.youtube.com/jtronicsTV

Twitter : https://twitter.com/jtronics2

Facebook : https://www.facebook.com/jtronics.de/

Paramètres d'impression 3D

trancheur : cura (veuillez prendre cura, ne prenez pas slic3r !)

Buse : 0,4 mm

mur : 3 Périmètre

soutien : uniquement pour la couverture

Optimiser l'ordre d'impression des murs : Oui

Remplissez les gabarits entre les murs : Non

les couches adaptatives : Oui avec la couche : 0,10 à 0,20 mm

matériel : PLA

remplissage : non (uniquement pour la couverture)

Optimisation des voyages de remplissage : Oui

Pas trop vite ! Imprimez les pièces avec environ 30mm/s, pour obtenir une bonne connexion des couches. (Cela dépend de la qualité de votre imprimante)

pas trop chaud, à cause de la buse à goutte PLA 205*C

  • Format du fichier 3D : ZIP
  • Dernière mise à jour : 2020/10/01 à 12h52
  • Date de publication : 2019/06/28 à 23h30

Copyright

©

Mots-clefs

Créateur

Page traduite par traduction automatique. Voir la version originale.

Collection associée à ce modèle 3D


Makes réalisés par la communauté

Meilleures ventes de la catégorie Jeu


Ajouter un commentaire

57 commentaires

Hello,

Yes, it's a cool model, but I've issues, may be due to the same cause , the boat weight when using the BLHELI ESC :

  • at full throttle, the boat goes underwater
  • the self-righting doesn't work

I've try the Littlebee ESC + Recom DC/DC but at the middle of the throttle, the motor changes the rotation way. I've build 2 Littlebee + DC/DC, but I've the same thing on both.

The pack of red brushless motor has a 3mm axe.

I think I'll build the 300 mm Jetboat which seems to be more stable.

I didn't resolve the bow going underwater on this model, but had similar issues on the 300mm model and I modified the stator where it meets the hull, so the stator/nozzle angle slightly up at the back (i.e. I "trimmed" the top edge of the stator flange, and aligned the prop shaft end support in the stator to match). If I recall correctly it was only a 3 degree change, but it makes all the difference. It would be nice to have a way of adjusting the stator/nozzle pitch angle by a few degrees, but it is beyond my design skills.

Hi @Brucekeen,
Thank you for your feed back, I'll try to change the output flow angle. Have you try without stabilizators ?

@jtronics, any idea to solve our issues ?

Thank you ;-)

Nice model with good detail. One problem I have is that at full throttle the boat drives itself underwater. The equipment is put as far back as I can, and the trim looks correct at low speed, but the faster I go the lower the bow gets, until it eventually goes straight under the water, just like a submarine! Any tips? My thought was to modify the stator/nozzle slightly to angle it up a few degrees.

FYI, I found brim build plate adhesion was necessary to stop the self-righting cover from warping (when it warped then didn't create a good seal)

@ThomasLucas What do you meant? I don't know anything about your battery. My boat runs with my 2x 18650 batteries about 15min.

Hello,

With battery in place, how much times can we play before the battery are too weak ?
Best regards, Thomas

@andybalg Hi andybalg, It is enough if you post your question only one time.
I don't know what are you doing with an arduino. You don't have to program anything.
Connecting the ESC and the Servo to your receiver should be really easy.

Hey there, we've sucessfully printed, soldered an built this cool model,

BUT I struggle heavily with ESC Settings - programming using an Arduino works, but I cannot get this motor to work.
I'd also suggest, that the electronic topics (How to solder balancing cable to LiPo, ESC setup and use of voltage regulator would be very helpful (at least for me) - So far the boat and has been built and soldered, and everything works, but the motor only beeps, but does not spin up correctly.

The Motor ist 2-3s . Does it really Work on 4s? Is the Jet drive able to use that much power without Kavitation?

has anyone tried this on a 3S battery?

Thank you!

@alexlev
Download the full packet again.
You could download the bought project so often you want, with all updates.

How can I download "20200603 added motor_180_ adapter.stl"
Full packet I downloaded early.

@joengelke
- print the screw with a smaller hole, there are some settings for better results in the slicer software
- grind the shaft flat in place of the screws
- use some glue

I have problems connecting the propeller to the shaft. It is working for the first few seconds then it is turning losse. Do you have an idea how to tighten the set screws or is there another trick to tighten prop?

@giacomoborghi02 I added a link to a lipo charger

@giacomoborghi02 the "boat_cover.STL" file in the v001 folder. It's the old version.

where can I find the stl of the flat cover

The problem was the ESC configuration.
BLHeli has solved the problem :)

@martijnsan Thanks for helping @Mc_KaNaN

@ Mc_KaNaN swap any two motor wires to reverse direction.

When accelerating until it reaches 50% of the travel, the motor does not move, but when it reaches 75% it begins to turn in the opposite direction.
Any idea?

@ Mc_KaNaN
you could use every cable you want. If you need more Information to the electronic stuff, you will find here: https://youtu.be/PmzOpirWdwc

Hi Stefan, I answered you via Facebook.

Hey Jtronics,

thanks for this design. I have printed the boat_hull.STL in the v002_stl Folder with Cura 4.5 / Ender 3.
The print turned out fine, but there is an issue at the bottom of the jet inlet.
The wall thickness there is so small, that Cura seems to have problems slicing it. It turns out asymmetric.
The Option "Print Thin Walls" changes the issue a little, but it is still visible.

Please have a look: https://www.dropbox.com/s/qrf5uo8elz9qry7/Jet_asymmetrisch.jpg?dl=0

I have sliced with same settings the V001 Model. There is no issue, the jet inlet looks symmetric.

Thanks,
Stefan

I have slice

Hello Martijn,
thanks for the info. I checked it. Yes there was a bug in the parts "boat_hull_split_a" and "boat_hull_split_b" .
But now it is fixed.

Thank you
jtronics

Hello, thanks for the great design. I'm having a lot of fun building together with my son.

Question: we've printed boat_hull_split_a and boat_hull_split_b from the v002 stls. However, the b part is slightly smaller on the mating surface of the a part, it doesn't fit... I've measured the stls in a cad program and they are indeed different.

Could you please release a new set of files that match?

Thanks a lot.
Martijn

Please what support in cura do you use?

What's the difference between v001 and v002? It's not clear from the discription

What's your problem? The links are working.

Could someone pass me the purchase link of these two components on AliExpress?

1x servo brass tube OD 2mm, ID 1mm (servo rod), Length 10mm
1x drive jet bearing, brass tube OD 3mm, ID 2mm (drive rod Length 3mm, servo rod Length 10mm)

Okay :-).Thanks for the rapid answer! Until Yesterday it was also at Aliexpress not available. Thanks god a lot :-) . I have a further question. Is it possible to link your Cura settings? I know you could have an other printer. But I have overtook your settings from the Images. But what is confusing for me. I have in the same Print-Time the twice in filament consumption. And I can't find out why....

@KASU01 The "GS-2502 Nano Servo 2g" is avaiable. The part is linked. Please look to the part list (1x servo GS-2502).

Dear Team,

is there an alternative servo avaiable for the GS 2502 which fit's in the holder of the hull and in regard of the specs. Because the gs2502 is not more buyable in the online shops. Perhaps you can give me a hint. I have tried to find one with nearly the same dimension, but it's very difficult.

If Iook in the comments, it seems there is no support since a longer time ?!

Hope you ca help and answer me please.

Sería posible un plano de conexiones de los componentes? En el video no se ve claro donde va soldado el DC converter. Gracias!

Hi ,
May be it is out of subject question, what is the program you used to generate the animated gif of this model

Hi, the holes are for additional parts like fins or trim plates. But in moment I found no time to test these parts. I will update the print settings with more details.
Not to fast 30mm/s, to get a good layer connection.
not to hot, because of dropping nozzle PLA 205*C
15% infill
walls before innfill & Ouline walls before inlines

Great Project, and thanks for sharing. I've bought it yesterday. Why are there 3 holes on the back on every side? The jet stator doesn't need them all? And are there any other print parameters like Infill, speed. And do you also have a 0,4 Nozzel and regardless 0,35 from your pictures is correct?

PS: A version with swappbale batteries would be great

Having real trouble printing the hull on an Artillery Sidewinder - keeps failing on the really thin part where the waterproof sealing tube goes - is there anyway to amend the file to reinforce this slightly ? the rest of the hull prints perfectly - I am using Prusa Slicer so that maybe the problem

Quick question what do you use to charge the batteries ?

I didn't receive a message. you could also contact me on thingiverse, there you could send pictures.

Hi, I think you forgot to contact me :-(, I send you chat messages to your FB account regarding the strange lines on the hull

Bonjour,
J'ai une radio 2 voies à volant avec son récepteur 6v que j'utilisais avec une voiture RC et j'aimerais savoir si je peux m'en servir pour votre bateau RC.
Merci,
A+++

Podrian recomendar un mando de control y receptor? video del ensamblaje de la parte electronica? gracias

I have send messages via FB chat

Please give me your e-mail? I will contact you.

Hi have some strange lines on the hull, try S3D 4.1 and Cura 4.2.1, same result.
Printed in Prusa I3 MK3 and Ender 3, same result!
you see it even in Cura when you preview the slicer
any suggestions to resolve this?

Muchas gracias por el vídeo del ensamblaje, me gustaría saber que mando de control y receptor podría comprar y que sea económico, y si es posible añadirle un chip para cargar las baterias. gracias!

Por cierto faltaría el enlace a un mando de control, a poder ser economico y compatible, gracias!

Hello alopezrobles88,
Last weekend, I printed all parts again and made a lot of video material of the assembling. I think the video will be ready at the end of the week.

Un proyecto muy bonito y divertido, espectacular. El fallo es que no venga con los planos de montaje de toda la parte electrónica y mecánica, para los que no sabemos de electrónica iría muy bien para poder realizar este proyecto y disfrutarlo con los mas pequeños de la casa.


Vous souhaitez soutenir Cults ?

Vous aimez Cults et vous avez envie de nous aider à continuer l’aventure en toute indépendance ? Sachez que nous sommes une petite équipe de 3 personnes et qu’il est donc très simple de nous soutenir pour maintenir l’activité et créer les futurs développements. Voici 4 solutions accessibles à tous :

  • PUBLICITÉ : Désactivez votre bloqueur de publicité AdBlock et cliquez sur nos bannières publicitaires.

  • AFFILIATION : Réalisez vos achats en ligne en cliquant sur nos liens affiliés ici Amazon ou Aliexpress.

  • DON : Si vous voulez, vous avez la possibilité de nous faire un don via PayPal ici.

  • BOUCHE À OREILLE : Invitez vos amis à venir découvrir le site et les magnifiques fichiers 3D partagés par la communauté !