Ir al contenido

Atención amigos, esto no es un mensaje privado sino un hilo de discusión público. Es un lugar de intercambio, gracias por ser cortés y respetuoso. Cualquier solicitud comercial o maliciosa será eliminada. Si mencionas un diseño en particular, no dudes en añadir el enlace o el título del diseño en tu mensaje para que la conversación pueda ser dirigida adecuadamente. Si quieres adjuntar fotos a tu post, no dudes en subir tus imágenes a un servicio gratuito de alojamiento de imágenes en línea como Imgbb y copia/pega los enlaces a tus imágenes en tu comentario. Tengan una buena discusión!

Escribe tu mensaje:

25 commentarios

Hi, I'd just like to ask if you allow the sale of models printed from your files?

Hi, not in general, but you can send me an email with the models you are interested in and we will surely find a solution :)

I tried the photon slicer and lychee slicer. I ended up loading it into auto desk and rebuilt it. It seemed to slice fine after that. Still have another 9 hours on the print before ill know for sure it printed right but I think the problem is resolved.

I just tested an older version of Photon_workshop and i think i found it.
I´m already on it and will uplodad an updated version in a couple of minutes. Maybe you can take a look and tell me if the error still occurs :)

I just uploaded a version where Photon_slicer seems to work fine with.

Would be great if you could take a look and give me some feedback,if it works now - even if you already found a fix for youself (maybe there are others who encounter the same problem)

Thanks for your help :)

been trying to print the RACHEL AND VERA WATER SPROUT model and everything is good until i slice it. The drain hole isn't printing right. it appears as if part of the tube is offset in a -z position so the base ends up with a slot in it and the tube ends up blocked. Is there any way I can revise the file so it will print right?

Hi, thanks for your message. This is strange, i didn´n encounter any problems with chitubox - but i´m sure we will find a solution for this.

Which program do you use for slicing?
Maybe you can send me a screenshot where i can see the exact position of the part that causes problems via email?

Meanwhile i will doublecheck again with different slicers.

Looking forward to hear from you soon :)

Hope you're doing good ^^
Was wondering if you'll keep doing the goblin exterminators series in the future ;)

I´m fine,thanks.
Unfortunately some construction workers destroyed the local internet distribution node a few weeks ago and the repairs took longer than expected, since some electronic spareparts are currently hard to come by.

Plus i live in an area that´s exactly between 2 gsm radio masts - and both are out of range; so i´ve been without internet connection for some weeks now.

But hey - in the middle of next week, the repairs are supposed to be complete. Sothere is light at the end of the tunnel ;)

and the exterminators are definetely to be continued... :D

  • 1 me gusta

was ist mit den goblin girls passiert ? wieso hast du die nicht mehr drinnen ?

Sollten alle noch da sein - ist evtl. dein safe-filter eingeschaltet?

MTB BICYCLE SCALE MODEL: Can you tell me what scale this was modeled in? Thanks...

The scale was supposed to be approx 1/87.
I just checked the measurements again and it actually seems to be 1/84, so if you would print it in life-size, the bike would be 26mm too long.
But, from the attached Blend file, you can export a new STL at a scale factor of 0,96 what should reduce the difference in length down to approx. 1-2mm.

Have fun :)

  • 1 me gusta

I do CNC and ur chubby girl model won't carve correctly. See previous messages. Dan

Is this model for 3d printing only or can it be used for CNC?

Just read a view lines about comparism of normal 3d printer and CNC - interesting...
Since CNC is a subtracting process, the models actually might need a different construction.

I can just guess - (you will propably have more knowledge and might be able to help me out a bit) - for the normal 3d printers, i think there is no problem if multiple faces and structures meet within a all-solid area - as long as they are all solid as well. If we now invert this because we are trying to use a subtracting contruction method, the clashing faces might confuse the respective software.

Have you already successfully printed another model of this kind so i can take a look at the construction?

I have set up a rotary carve in V Carve Pro and the model gets cut through top and bottom. This means that when it is carved it will separate before completion. Any suggestions?

did this happen on a specific model? In this case, please tell me which one is affected and i´ll try to fix this asap.

I haven´t tried V Carve yet, so i propably won´t be of much help if it is a software-specific problem, but in this case maybe you can send me some screenshots of the problem on my email and i will try to help


The model is chubby girl Sandra

That´s good news, because i updated just this model yesterday after i received a hint that the model had a corrupted base-plate. Nothing serious, but the normals were heading in the wrong direction. I corrected this and re-upped the STL.

The new file is named "Snd_updt.stl"

If you still got the old version, please reload the model and give it a try.

If there is still a problem, please tell me. :)

No change. Perhaps it is in the setup in my software.

I´ll take a closer look at this tomorrow.

i tested the trial version - but i doon´t see a problem yet.

Is it a specific step where the problem occurs? Can you already see the problem after importing the STL?

Hello I have a question. Some time ago you had a set of models of 2 ladies in a chair with some young girls standing around it and one on the lap of one of the women. What happened with that model. I wanted to purchase it but I can't find it anymore.

I hope this finds you well, are you producing more content any time or have you moved platforms, such as a patreon or such?
I absolutely love all the goblins and futa sculpts and cannot wait to print them out and start painting them!
But honestly, I want more!

Cheers to you and yours!

Hey, I really love all of your work here! Any more goblin things you could do are the best, if you could do more stuff with the sexy glasses futa goblin that would be amazing!

you're an inspiration friend!

Servus - and thanks, great to hear that you like ´em.

I´m currently working on a different one, but we´ll surely see more of that little naughty one ;)

Have fun

Yessss! If you need any fun ideas, have you thought of futa docking gobbos leaking into each other?

Hey There,

My name is Max Stein and I’m a designer in Portland, Oregon. I’m creating a fun, goofy, adult-themed book and would love to use your 3D model as part of the design for one of the pages.

Your model will appear as part of a derivative abstract composition.

I purchased your model from CULTS-3D and see that it is copyright protected. I am reaching out to politely request for your permission to non exclusively use your design in my book. Would that be something you would be open to?

Please let me know if you’d be open to this or have any questions.

Really love your work and thanks for your time.


Love the dirty mind. I do some rigging and design work, I'm interested in starting a conversation if you like. Please let me know if you are interested at all....I have a couple of great has a dragon....He's happy with your goblin

J'adore votre univers, j'ai imprimé et mi la jeune fille gobelin jardinière coquine dans mes petites plantations de mon balcon, ci il y a un mail, je vous envoie des photos
voire mon compte, c'ai une adresse mail


I love your universe, it makes me hard

Hi Matthias,
the file from Futa boss raid currently works.
The Zip should be at appr. 30Mb and contains a single file "5.stl".

Maybe there was a problem on the server, so just try again and you should be fine.

Or is there something else you are missing?



i miss the other part of the demon-futa-boss-raid-fail,
have you this not on publish on 3cults?

the models of all the goblins very nice designed from you :-)

i'm a Beginnes of the 3D print with FDM (PLA on the Moment)

best regards
Matthias from Germany

Follow me on Cults3d to see my 3d designs !!!
💥💥👉 Everyday I upload new designs and once a week I also upload a free to download design.

👇 You can follow me here...

hello I was just on thingiverse an you poster Meru the succubi Great work !1 but there is a issue with the base ware the supports go threw the base directly to her feet. also the meru with the hammer give the error 404 code.

Thank you for the sexy goblin girls! Do you have a web site or patreon where we can continue to appreciate your work?

Thank you for the fantastically done myriad of sexy goblin girls! Do you have a patreon or anything like that?

Merci beaucoup


Bravo pour votre travail, j'aime beaucoup