Ir al contenido

Pistola de goma XDSR

Descargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3DDescargar modelos 3D Pistola de goma XDSR, WW3D

Makes hechos por la comunidad

¿Usted imprimió 3D este modelo?

Descripción del modelo 3D

https://youtu.be/znnO-5fZpPA

Actualización Cambié el cargador para que se deslice fácilmente pero se mantenga en su lugar.

Actualizar Añadí un tapón de barril para que si decides imprimirlo en negro puedas ponerle una punta naranja.

Esta pistola de goma modelada a partir de una Springfield XDS 9mm se imprime en el lugar, no requiere montaje. Así es, sin ensamblaje, sin pegamento, sin tornillos. Sólo quita la carga de los soportes y dispara. Incluye un cargador extraíble para guardar munición extra. Dispara las bandas elásticas #31 , así que no hay necesidad de gastar dinero en municiones para pistolas de bandas elásticas.

Abajo hay un enlace a las bandas elásticas para las que está diseñado. Si usas gomas más fuertes, o cargas más de cuatro disparos, puede resultar en una falla del rotor.

Alliance Rubber 96315 Advantage Rubber Bands Tamaño #31 , 1 lb Caja contiene aprox. 850 bandas (2 1/2" x 1/8", Rojo) https://www.amazon.com/dp/B008X09PDC/ref=cm_sw_r_cp_apa_i_Pp.KCb72JE91W

Porque es una réplica muy detallada de un arma de fuego real, sólo imprímela en colores brillantes para evitar que sea confundida con la real.*

Parámetros de impresión 3D

Altura de la capa: 0,2

Soportes: Sólo desde la placa de construcción, si estás usando soportes a medida asegúrate de que el rotor y el eje giran sobre sí mismos. También quita cualquier soporte que se extienda hacia arriba en el cuerpo, ya que será difícil de quitar.

También recomiendo aumentar la densidad de soporte al menos hasta el 50% o usar una capa de soporte densa para asegurarse de que la textura de las empuñaduras salga bien.

4 proyectiles

Relleno: 30%

Oriente el modelo de manera que el cañón apunte hacia arriba y se incline en un ángulo de 15 grados hacia la parte superior del cañón como se ve en la foto.

  • Formato de archivo 3D : STL
  • Tamaño del modelo 3D : X 26 × Y 110 × Z 160 mm

Palabras-clave

Creador

Designs 18
Descargadas 1565
Seguidores

Hi, my name is Walt, I am a Retired United States Marine. Thanks for checking out my designs. If you want to see more of my designs and prints check out my Instagram @waltswoodworksand3dprinting, or watch my videos on YouTube @waltswoodworks3d.

Copyright

©

Página traducida por traducción automática. Ver la versión original.

Los más vendidos de la categoría Variado


Añadir un comentario

16 comentarios

I uploaded a picture of the supports. However I suspect your problem is more with your support settings, or temerature being too high. Supports shouldnt be so hard to remove that they break the part. Message me on Instagram or gmail, links in bio, if you need any more help.

Hi. Could you post a pic of your supports from beneath the build plate? I got close on my first try, but broke the back off trying to remove a support.

I see no reason why. They print fine on a Creality Ender 3

Thanks for the fast reply ,I found the setting and sorry for bothering you. Thanks!

Read the printing directions, select "supports from build plate only" in your slicer. This will keep it from generating support inside. Also tilt the gun at a 15 degree angle towards the top of the barrel. Let me know if you have anymore questions. My Instagram and email are in my profile.
Happy Printing!

I just bought this and was wondering if its okay if there are supports in the model. If not, do you have an stl with the correct supports for it to work.

This one should be no problem then, it is much smaller than the 1911. Happy Printing!

awsome thank you. I printed your 1911 but I only have 180x 180 y 200z. I had to make it go from corner to corner and put it at a steeper angle than the 15 degrees you recommended. It still came out alright. one of the rotor nubs was messed up but it still functions.

About 25x, 110y, 160z, any of my guns can be printed on a Ender 3 or Prusa MK3

what are the build volume requirments?

I added a magazine with tighter tolerances for anyone who is having issues with the mag falling out.

Took a couple tries to dial in my setting to make this bad ass print. I had to use my .4mm nozzle and .2 layers. My .5 mm nozzle was just to tight for the tolerances. I think it took me between 5-8 min of cleaning out supports for freeing up the action. Once it was free it shot rubber bands right a way. Awesome job!

Printed on a mk3. Crash was detected about 18 hours into the 20 hour print. First crash on my machine ever. After the crash was detected it reoriented the extruder and continued the print, but it was off a few inches so unfortunately I cancelled the print.

Gun still functions as it was past the top catch for the bands, but I'll have to look at the file and see what the hang-up is as both of your guns have to be at the right angle to fit a prusa. Slicer has my profiles and didn't show it as printing out of the build area.

Kinda bummed, wanted to snag the 1911 as well and print that too but that's an even larger print so I'll try to get this printed fully first.

Magazine does slip out so I might edit the thickness or add some bumps. Also, can your next design have a rubber band gun that shoots harder/further? Using your reccomended ammo and wish I could get about double the distance. Don't know if that would mean a lot bigger "gun" or just a quirky design which would stretch the ammo more and have a different release point.

Or, maybe make a "screw on" silencer by threading the original gun and silencer which could the. Be added to either weapon and increase shot distance by increasing the bands stretch before firing.

Love the work either way. Just gotta get it 100% now and try to get you to make a "silencer" which real Function is increasing shot distance.

Keep up the great work.

Thanks for downloading. Let me know if you have any problems, and please share pictures of your print. If you are on Instagram tag me @waltswoodworksand 3dprinting

Very Cool! Thank you for your service! I enjoyed my time in. If this prints well on my printer, I'll be sure to nab up your 1911!


¿Te gustaría apoyar Cults?

¿Te gustan Cults y quieres ayudarnos a continuar la aventura de forma independiente? Tenga en cuenta que somos un equipo pequeño de 3 personas, por lo que es muy sencillo apoyarnos para mantener la actividad y crear futuros desarrollos. Aquí hay 4 soluciones accesibles para todos:

  • PUBLICIDAD: Deshabilite su bloque de anuncios AdBlock y haga clic en nuestros banners.

  • AFILIACIÓN: Haga sus compras en línea haciendo clic en nuestros enlaces de afiliados aquí Amazon, Gearbest, Banggood, Aliexpress o Ebay.

  • DONACIÓN: Si lo desea, puede hacer una donación a través de PayPal aquí.

  • PALABRA DE BOCA: Invita a tus amigos a venir, descubre la plataforma y los magníficos archivos 3D compartidos por la comunidad!