Ir al contenido

F1 Mclaren MP4-30 2015 Steering Wheel.

Descripción del modelo 3D

Mclaren MP4-30 2015 Steering Wheel full scale replica.

129 pieces relatively easy to print with the 0,4mm nozzle and simple assembly.

It is a model that requires a little more time than a single print piece but in my opinion the result is spectacular.
I hope you like it as much as I do and that you enjoy its printing and assembly.
I have tried to simplify the design of the pieces to facilitate their printing and assembly.
In total there are about 129 pieces.

Soon the steering wheel exposure stand.
The terrible vid
https://www.youtube.com/watch?v=PbnNEwm4Kkw

Parámetros de impresión 3D

First I will indicate the CURA general print settings and then detail them for each piece

Nozzle: 0.4 mm
Layer Height: 0.2 mm - According to piece
Line Width: 0.35 mm - According to piece

Wall Line Count: 3
Top/Botton Line Directions: According to piece
Activate “Outer Before Inner Walls”
Initial Layer Horizontal Expansion: -0.1

Infill Density: According to piece.

Infill Speed: 60 mm/s
Outer Wall Speed: 20 mm/s
Inner Wall Speed: 35 mm/s
Top/Botton Speed: 25 mm/s

Support: According to piece
Support Over Hang Angle: According to piece
Support Density: 15%
Support Interface Thickness: 0.6 mm
Support Interface Density: According to piece

IMPORTANT!! The pieces are in their printing position.

Printable parts:

• 1xSW_Body_Front_A: Aprox.Time: 7 h. Material: 58 gr.
Infill Density: 10%
Support: No
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Body_Front_B: Aprox.Time: 6 h. Material: 51 gr.
Infill Density: 10%
Support: Yes
Support Over Hang Angle: 75º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Body_Back_A: Aprox.Time: 7 h 30 min. Material: 72 gr.
Infill Density: 10%
Support: Yes
Support Over Hang Angle: 75º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Body_Back_B: Aprox.Time: 10 h 15 min. Material: 100 gr.
Infill Density: 10%
Support: Yes
Support Over Hang Angle: 75º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Paddle_Shifter_A: Aprox.Time: 2 h. Material: 14 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 65º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Paddle_Shifter_B: Aprox.Time: 1 h. Material: 10 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Paddle_Shifter_C_Left: Aprox.Time: 1 h. Material: 7 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 65º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Paddle_Shifter_C_Right: Aprox.Time: 1 h. Material: 7 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 65º
Recommended filament: Fillamentum Vertigo Grey.

• 1xSW_Button_Case_Left: Aprox.Time: 1 h 30 min. Material: 11 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Button_Case_Right: Aprox.Time: 1 h 30 min. Material: 11 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Display_Case: Aprox.Time: 2 h. Material: 15 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 75º
Recommended filament: Fillamentum Traffic Black.

• 10xSW_Button: Aprox.Time: 5 min. Material: 1 gr.
Line Width: 0.3 mm
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Handgrip_Left: Aprox.Time: 3 h 45 min. Material: 37 gr.
Z Seam Alignament: User Specified (hold in the side)
Infill Density: 10%
Support: Yes (not change the piece inclination)
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Handgrip_Right: Aprox.Time: 3 h 45 min. Material: 37 gr.
Z Seam Alignament: User Specified (hold in the side)
Infill Density: 10%
Support: Yes (not change the piece inclination)
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Display: Aprox.Time: 1 h. Material: 7 gr.
Top Layers/Bottom Layers: 2
Top/Bottom Line Directions: [180]
Infill Density: 15%
Initial Layer Speed: 15mm/s
NO Cooling.
Glass Plate (min.heat 40ºc)
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Case_Leds_Display: Aprox.Time: 25 min. Material: 2 gr.
Infill Density: 15%
Initial Layer Speed: 15mm/s
NO Cooling.
Glass Plate (min.heat 40ºc)
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Leds_Display: Aprox.Time: 14 min. Material: 1 gr.
Infill Density: 15%
Initial Layer Speed: 15mm/s
NO Cooling.
Glass Plate (min.heat 40ºc)
Support: No
Recommended filament: Fillamentum Traffic White.

• 1xSW_Sticker_ Button_+10 (Blue/White)
• 1xSW_Sticker_ Button_+1 (Blue/White)
• 1xSW_Sticker_ Button_N (Green/Black)
• 1xSW_Sticker_ Button_PLS (Yellow/Black)
• 1xSW_Sticker_ Button_OT (Yellow/Black)
• 1xSW_Sticker_ Button_red (Red)
• 1xSW_Sticker_ Button_X (Black/White)
• 1xSW_Sticker_ Button_D (Black/White)
• 1xSW_Sticker_ Button_+ (White/Black)
• 1xSW_Sticker_ Button_- (White/Black)
Aprox.Time: 2 min. Material: 1 gr.
Layer Height: 0.15 mm
Initial Layer Height: 0.2 mm
Line Width: 0.3 mm
Infill Density: 15%
Initial Layer Speed: 15mm/s
NO Cooling.
Glass Plate (min.heat 40ºc)
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 2.
Recommended filament: Fillamentum Traffic White, Traffic Black, Traffic Yellow Green Grass, Noble Blue, Ruby Red,

• 1xSW_StickerA_ Front_Selector (White/Black)
• 1xSW_StickerB_ Front_Selector (Red/White)
• 1xSW_StickerC_ Front_Selector (Black)
• 1xSW_StickerD_ Front_Selector (Blue)
• 1xSW_StickerE_ Front_Selector (Green)
Aprox.Time: 2 min. Material: 1 gr.
Layer Height: 0.15 mm
Initial Layer Height: 0.2 mm
Line Width: 0.3 mm
Infill Density: 15%
Initial Layer Speed: 15mm/s
NO Cooling.
Glass Plate (min.heat 40ºc)
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 2.
Recommended filament: Fillamentum Traffic White, Traffic Black, Green Grass, Noble Blue and Ruby Red.

• 2xSW_Big_Front_Selector_Wheel: Aprox.Time: 12 min. Material: 1 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Traffic White and Gold Happens.

• 2xSW_Small_Front_Selector_Wheel: Aprox.Time: 8 min. Material: 1 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Noble Blue and Gold Happens.

• 2xSW_Front_Switch: Aprox.Time: 24 min. Material: 2 gr.
Infill Density: 15%
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 49 (Layer Height: 0.2 mm)
Recommended filament: Fillamentum Traffic Black, Noble Blue and Rapunzel Silver.

• 3xSW_Front_Selector: Aprox.Time: 30 min. Material: 2 gr.
Infill Density: 15%
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 28 (Layer Height: 0.2 mm)
Recommended filament: Fillamentum Traffic Black, Noble Blue and Traffic White.

• 3xSW_Inner_Front_Selector: Aprox.Time: 4 min. Material: 2 gr.
Infill Density: 20%
Support: No
Recommended filament: Fillamentum Noble Blue and Traffic White.

• 2xSW_Side_Selector_Wheel: Aprox.Time: 25 min. Material: 3 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Ruby Red and Green Glass.

• 1xSW_Screw_ Side_Selector_Wheel: Aprox.Time: 1 min. Material: 1 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Rapunzel Silver.

• 1xSW_ Body_Hitch_Paddle_Shifter_C: Aprox.Time: 1 h 30 min. Material: 11 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 2xSW_Side_Switch: Aprox.Time: 11 min. Material: 1 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_HitchA_Paddle_Shifter_AB: Aprox.Time: 19 min. Material: 3 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_HitchB_Paddle_Shifter_AB: Aprox.Time: 9 min. Material: 1 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 1xSW_Hitch_Paddle_Shifter_C: Aprox.Time: 26 min. Material: 3 gr.
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 70º
Recommended filament: Fillamentum Traffic Black.

• 4xSW_Buttom_ Paddle_Shifter: Aprox.Time: 7 min. Material: 1 gr.
Infill Density: 15%
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 14, 22, 36 (Layer Height: 0.2 mm)
Recommended filament: Fillamentum Traffic Black, Rapunzel Silver and Ruby Red.

• 1xSW_ Body_Hitch_Quickly_Detachable: Aprox.Time: 7 h. Material: 56 gr.
Z Seam Alignament: User Specified
Infill Density: 15%
Support: Yes
Support Over Hang Angle: 70º
Post Procesing / Pause at layer (change colour): 77, 86, 95, 151, 158, 174. (Layer Height: 0.2 mm). View photo.
Recommended filament: Fillamentum Traffic Black, Vertigo Grey, Gold Happens and Ruby Red.

• 3xSW_Screw_Ring_Quickly_Detachable: Aprox.Time: 11 min. Material: 1 gr.
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Rapunzel Silver.

• 1xSW_Plug_Quickly_Detachable: Aprox.Time: 13 min. Material: 1 gr.
Infill Density: 15%
Support: No
Experimental: Activate “Enable Draft Shield” (purge filament change)
Post Procesing / Pause at layer (change colour): 25 (Layer Height: 0.2 mm)
Recommended filament: Fillamentum Traffic Black and Rapunzel Silver.

• 6xSW_Screw_A_ Front: Aprox.Time: 5 min. Material: 1 gr.
Fill Gaps Between Walls: Nowhere
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 4xSW_Screw_B_ Front: Aprox.Time: 5 min. Material: 1 gr.
Fill Gaps Between Walls: Nowhere
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

• 12xSW_Screw_ Back: Aprox.Time: 2 min. Material: 1 gr.
Fill Gaps Between Walls: Nowhere
Infill Density: 15%
Support: No
Recommended filament: Fillamentum Traffic Black.

  • Formato de modelo 3D : STL

Palabras-clave

Creador

Licencia

CC BY NC ND

Los más vendidos de la categoría Variado

Contenidos correspondientes


Añadir un comentario


¿Te gustaría apoyar Cults?

¿Te gustan Cults y quieres ayudarnos a continuar la aventura de forma independiente? Tenga en cuenta que somos un equipo pequeño de 3 personas, por lo que es muy sencillo apoyarnos para mantener la actividad y crear futuros desarrollos. Aquí hay 4 soluciones accesibles para todos:

  • PUBLICIDAD: Deshabilite su bloque de anuncios AdBlock y haga clic en nuestros banners.

  • AFILIACIÓN: Haga sus compras en línea haciendo clic en nuestros enlaces de afiliados aquí Amazon, Gearbest, Banggood, Aliexpress o Ebay.

  • DONACIÓN: Si lo desea, puede hacer una donación a través de PayPal aquí.

  • PALABRA DE BOCA: Invita a tus amigos a venir, descubre la plataforma y los magníficos archivos 3D compartidos por la comunidad!