Ir al contenido

Escuela de Brujería de Hogwarts

Descripción del modelo 3D

Una maqueta casi perfecta del castillo hogwarts de los estudios universales. Completo con un cajón oculto que sale del frente y una contención para poner hielo seco y ver la niebla rodar por los acantilados. Si quieres el resto de los mecanismos de los cajones ocultos y dónde poner los muelles para hacerlos funcionar, puedes mandarme un mensaje o dejar un comentario. Disfruta.

Parámetros de impresión 3D

.2mm de altura de la capa

relleno variable, principalmente 20%.

único perímetro

  • Formato de modelo 3D : STL



Seguidores Suscriptores 1
Descargadas 1155
Ventas $96



Página traducida por traducción automática. Sugerir una mejor traducción

Modelos 3D similares

Los más vendidos de la categoría Arquitectura

Añadir un comentario

44 comentarios

I will be adjusting the tongue and groove assemblies so they are easier to put together. It's good to use a little elbow grease now and again though. I suggest having a set of files near your printer at all times. They work wonders

Perfect gtoblade, great idea!

I know Nook, read all the posts!

Sorry but i am not the creator !!

I´m not the creator !!!

I also had issues with the tongue and groove connections. Had to work them. I ran lighting thru it and put a small speaker and programmable board under the back so it plays the theme to Harry Potter daughter loves it

I have printed it out at 0,6 scale of the original owing to the fact that my printing plate is small . It came together nicely, i had to work some on the groove and tongues as it seemed to be equal in size and a little tight to come together. Not much work. My nephew was very exited when he got it, and I think it is a beautiful model of the castle. No need to worry, just you start print it! Credits to the designer Valient!!!!!

Hi! I am looking to put this together as a special Christmas gift but am reading the comments and feeling nervous. Do I need to adjust the measurements before printing? Has anyone put this together and have any advice?

Nook isnt the creator. I am.

Can you post a picture of what you have together so far and I can better help you.

Sorry, but i don't have any Part.

I'm looking for themissing part of bedrock behind the Bell tower...

Are you looking for the dry ice basin cover? Or the yellow arch from the pictures?

Ok , si do you have any contact or mail to message the designer ?

Sorry, but i'm not the designer of this modell and i don't have missing parts.

Hi , thank for this amazing works , do you have the missing part behind the Bell tower ?
Thank you in advance

the movement brace holds up the landing under the spire.

I am not the creator of this magnicifent work. Look on the download on cults and you will see the owner of the files.

I am not the creator of this magnicifent work. Look on the download on cults and you will see the owner of the files.

Sorry, but i don´t have the parts.

The dry ice cap goes behind the great hall. Next to the spire dorms where the student housing is. Dumbledors office is at the top of the spire. There is a small basin that has pins which correspond to the dry ice cap placement.

Hello arnedh,
The Creators name is VALICNT. I only had download the file. I have a lot of questions, about the model, too. Sorry.

I wonder where the Movement brace comes in the model, and where you put the Dry ice cap! Do you have a picture showing these details?

Hello, can you send me the Stl-files for the missing parts, please.
My Email:
Thank you.

Thank you for the answer!

The drawer only works with a large base over the entire model. In the model i believe it is 7/8" thick. So you would have to measure the pieces to fit your model. The drawer requires small springs from a hardware store. And the locking mechanism is the tiniest. I will find a video of me putting the model together. Then post it on here.

I have printet the model in 60% size and everything came out beautifully. The not and pens had to be worked a little as I suppose they are drawn to the same size on the two parts going together. I would like a little more info on how the drawer comes together though. Must the model be placed on a wooden base to take up the difference in height before doing the drawer? I am totally impressed of your work. I am doing the model for my nephews bitrhday. He is a totally Harry Potter fan and been to both places, the one in Orlando and the one in London so I hope I will get it done. Keep up the good work. I have been doing computing for some time, but are new to 3D printing.

If your print material doesnt come out right*

If tour print . bacterial doesnt cone out perfectly without expansion between layers the tabs will be perfect. Also in the stl files they are .022 inches smaller on each side. Or .5mm smaller on each side.

Nice, however the tabs dont line up, they do but arent sized right, the male tabs are bigger than they should be, or the female part is too small. looks like it all will go together fine but the tabs are all messed up.

Hi everyone, valient6 here. If anyone wants instructions on how it goes together we can Skype and I can explain how to do it. My Skype is valient6. Otherwise you have to wait for the video of me putting it all together.

Hi everyone, valient6 here. If anyone wants instructions on how it goes together we can Skype and I can explain how to do it. My Skype is valient6. Otherwise you have to wait for the video of me putting it all together.

Hey thank you this is amazing! Do you by any chance have a list of the order to put them together? They are coming up alphabetically on mine

Ok i ordered the stl files in sequence of attaching them together. They really only go together one way. As the dovetails are not all the same dimensions. Start with each peice as i have them ordered and start sliding them together. I will have a video on how exactly they go together on youtube soon. The drawer needs a back to it. And a bottom. I will leave that part up to you. I made the entire inside of the drawer out of cedar wood so it will resist mold and smell great when you open it. The spring sizes are .08" diameter and .5" diameter and the larger spring is .75" long to preload the drawer. the small spring preloads the latch on the secret drawer to catch the notch on the inside of the great hall bedrock bedrock. There are two ledges on the bedrock that the drawer fits into on the right and left side.

The bedrock is underneath the structures. So the great hall bedrock goes ontop of the great hall bedrock bedrock. Sorry for the confusion. I will re order them from top to bottom. But on the west wing, the school bedrock side there are 3 peices that go together to form the single bedrock. And when you put it together the bridge has to go in at a certain time along with the school building as well. Bridge holds in the school structure and the bedrock holds in the bridge... Its a puzzle for sure.

can i have some kind of instruction and also the missing parts for this great model please ?

This model is amazing. Im going to make this for my sisters birthday. I would greatly appreciate the files for the drawer mechanism. Thank you so much.

For anyone who wants the secret drawer stl files i will upload that if you ask for them.


Belle création. Exceptionnel !



¿Te gustaría apoyar Cults?

¿Te gustan Cults y quieres ayudarnos a continuar la aventura de forma independiente? Tenga en cuenta que somos un equipo pequeño de 3 personas, por lo que es muy sencillo apoyarnos para mantener la actividad y crear futuros desarrollos. Aquí hay 4 soluciones accesibles para todos:

  • PUBLICIDAD: Deshabilite su bloque de anuncios AdBlock y haga clic en nuestros banners.

  • AFILIACIÓN: Haga sus compras en línea haciendo clic en nuestros enlaces de afiliados aquí Amazon, Gearbest, Banggood, Aliexpress o Ebay.

  • DONACIÓN: Si lo desea, puede hacer una donación a través de PayPal aquí.

  • PALABRA DE BOCA: Invita a tus amigos a venir, descubre la plataforma y los magníficos archivos 3D compartidos por la comunidad!