Skip to content

Vario Lynx 1:8 external scale detail parts.

?
Creation's quality: 5.0/5 (3 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 10.3k views
  • 17 likes
  • 12 downloads

3D model description

This is a list of many panel doublers and other scale detail for the Vario Lynx fuselage.

Also check out my other Vario Lynx accessories:
http://cults3d.com/en/various/replacement-nose-for-the-vario-lynx
http://cults3d.com/en/various/vario-lynx-1-8-scale-cabin-and-cockpit-doors
http://cults3d.com/en/various/vario-lynx-cockpit-interior
http://cults3d.com/en/various/scale-helicopter-seats-westland-lynx-1-8-seats

Lynxguide.zip - Photos showing the placement on my Lynx.Should be better wuality than the ones shown here.
Wheellock01.stl - Dummy wheel locks for one main and one nose wheel.
Wheel01-03 - Wheels and tires for the nose and main wheels.
Antenna01.stl - Belly antenna and collector tank covers.
Ice01.stl - Ice accretion indicator for right side under cockpit door.
Pitot01.stl - Pitot tube.
Flotation01.stl - Front flotation bags.
Tiedown01.stl - Sponson tie down shackle.
Tiedown02.stl - Nose tie down shackle.
HF01.stl - Forward HF antenna with mounting base.
Fuelvent01.stl - Fuel ventilation pipe.
Sidestores01.stl - Bottom side stores eyelets and belly panels.
Sidestores02.stl - Top side stores eyelets.
Footstep01.stl - Fuselage side footsteps.
Mainfuel01.stl - Main fuel tank panels and air intakes for aft compartment.
Fuelcap01.stl - Main tank gravity fuel filling ports.
Cockpitdoor01.stl - Dummy cockpit doors, handles and latch (for locking in open position).
Wiper01.stl - Windshield wipers.

Rooffairing01.stl - Extension for the bump between the roof windows. Requires adaptation and filling.
Roofpanel01.stl - Panel in front of sliding fairing (doghouse).
AC-intake01.stl - AC generator air intake for roof fairing front.
Sliding01.stl - Rail stop in front of roof sliding fairing
MGB-footstep01.stl - Dummy footstep panels.
Collar01.stl - Filleted ring for blending the area around the main rotor.

Nose03.stl - Douple panels for the joint between the nose and fuelage, bottom and top pieces.
Panel01.stl - Panel doublers fuselage sides below engine cowlings.
Panel02.stl - Panel doublers fuselage sides in front of tail joint.
Panel04.stl - Panel doublers in front of and behind cockpit doors.
Panel06.stl - Panel doublers fuselage sides along panel line.
Panel11.stl - Inset panel under cabin doors.
Navlight01.stl - Cockpit footsteps and nav light units.
Extpower01.stl - External power panel.
Fuelpanel01.stl - Fuel pressure filling access panel for right side.

Aftcompartment01.stl - Aft compartment door.
Nosegearfairing01.stl - Fairing that fits around the nose gear.
Nosegearfairing02.stl - Same as above, but with larger hole if needed.
Sponson01.stl - Root trailing edge fillets for the sponsons. Remove material to fit them.

Exhaust01.stl - Shapes for creating filleted openings for the ducts.
Exhaust02.stl - Exhaust ducts for 50 mm fan.
Tailfairing01.stl - Covers between exhaust duct fairings.
Intake01.stl - Engine air intake leading edge and detail parts.
Coolerintakes01.stl - Engine oil cooler and accessories cooler intakes.
Engcowllock01.stl - Guides for wire lock on the top between the engine cowlings.
Bump01.stl - Bumps and doublers for the engine cowlings.
Enghandle01.stl - Engine cowling locking handles and bump stops.

IGB01.stl - Tail intermediate gearbox fairing parts.
Tailplane01.stl - Shortened tail plane with gourney flap.
Shaftcover01.stl - Tail drive shaft cover doublers. Glue over the tail shaft bump on the tail.
Trailingedge01.stl - Access panels for the left side of the tail fin trailing edge fairing.
Tailpanel01.stl - Lifting holes and doublers for the tail boom.
Tailpanel02.stl - Tail fish plate and tail fin doublers for left side.
Tailpanel03.stl - Tail fish plate and tail fin doublers for right side.
Tailpanel04.stl - Overlapping panel for the tail boom.
Tailpanel05.stl - Overlapping panel for the tail boom. Trim length to fit in the rear.
Tailpanel06.stl - Overlapping panel for the tail boom. Trim length to fit in the rear.
Antenna02.stl - Tail boom bottom center antenna.
HF02.stl - Middle and rear HF antenna posts.
Anticollision01.stl - Anti collision lights for the top of the tail.


3D printing settings

Print as they open. I usually print small parts with 100% infill.

3D printer file information

  • 3D design format: STL and ZIP Folder details Close
    • AC-intake01.STL
    • Aftcompartment01.STL
    • Antenna01.STL
    • Antenna02.STL
    • Anticollision01.STL
    • Bump01.STL
    • Cockpitdoor01.STL
    • Collar01.STL
    • Coolerintakes01.STL
    • EngHandle01.STL
    • Engcowllock01.STL
    • Exhaust01.STL
    • Exhaust02.STL
    • Extpower01.STL
    • Flotation01.STL
    • Footstep01.STL
    • Fuelcap01.STL
    • Fuelpanel01.STL
    • Fuelvent01.STL
    • HF01.STL
    • HF02.STL
    • IGB01.STL
    • Ice01.STL
    • Lynxguide.zip
    • MGB-footstep01.STL
    • Mainfuel01.STL
    • Navlight01.stl
    • Nose03.STL
    • Nosegearfairing01.STL
    • Nosegearfairing02.STL
    • Panel01.stl
    • Panel02.stl
    • Panel11.STL
    • Pitot01.STL
    • Rooffairing01.STL
    • Roofpanel01.STL
    • Shaftcover01.STL
    • Sidestores01.STL
    • Sidestores02.STL
    • Sliding01.STL
    • Sponson01.STL
    • Tailfairing01.STL
    • Tailpanel01.STL
    • Tailpanel02.STL
    • Tailpanel03.STL
    • Tailpanel04.STL
    • Tailpanel05.STL
    • Tailpanel06.stl
    • Tailplane01.STL
    • Tiedown01.STL
    • Tiedown02.STL
    • Trailingedge01.STL
    • Wheel01.STL
    • Wheel02.STL
    • Wheel03.STL
    • Wheellock01.stl
    • Wiper01.STL
    • intake01.STL
    • panel04.STL
    • panel06.stl
  • Last update: 2019/02/27 at 04:03
  • Publication date: 2017/04/01 at 02:37

Copyright

©

Tags

Creator

Norwegian inventor/designer/cat owner.

Please don't ask for original design files or parametric files.

If you ask a question about a design, ask under the design so that I can answer there.

Issue with this design? Report a problem

Collection associated with this 3D model


Best sellers of the category Various


Add a comment


Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon or Aliexpress.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!