Skip to content

My3Dboat 640x470x250 bait boat

Creation's quality: 5.0/5 (2 votes)
Evaluation of members on the printability, utility, level of detail, etc.

3D model description

bait boat by My3dBoat is licensed under the terms of the Creative Commons Attribution-NonCommercial-NonModification 4.0 International license.

join us on Facebook

!!!needs a 300x300 CR10 style tray!!! to print it.

Bait boat for carp fishing.

Winch with submarine camera mounted with two micro switch to stop the winch on the way up.

provided with two interchangeable trays in 2 minutes.

a standard tray that can accommodate the primer and the assembly or a tray with a worm screw and a wide line at the back.

for the assembly of the printed parts it will be necessary

-Sika11 fc glue

-a few M3 screws

-a 4 mm aluminium tube for the winch and the cover bar

-A 16 mm hollow aluminium tube (for the two internal reinforcements)

-A piano wire or a piece of filament is enough to act as a hinge pin for the classic tray.

*optionally :

:- glass cloth and resin to reinforce the junctions of the interior.

-Dû mastique


and common sense will be needed.

test of the boat

test of the single bin

test auger bin

test camera winch

test of the wide line

list of the material used

I specify that the links are for information only and are not affiliated.

a radio 6 channels minimum but a 10 channels will be more suitable style fsi-6X

U-joint to close the hull

Black adhesive foam Epdm 10X4 MM for sealing between top and bottom

2 servo 360° worm gear tray and video winch

Servo 360

2 sealed for winch end of travel

micro switch

1 zeener for winch connection

2 motor c3548 790kv ( 500kv is enough )

2 Transmission Connector 4mm/5mm

2 stainless steel shaft for boat A Length L20cm

1 pair Rocker switches, marine for car, 12V, 25A

12V 10mm pre-wired White and red LED ( optional )

2 Mini digital voltmeter tester DC 4.5 V to 30 V ( optional )

25T round aluminium spreader bars for the worm gear tray and the winch

5.8G 3-channel 3-channel video switch module ( optional )

underwater fishing camera 1000tvl 10meters

22mm electric line collector for video winch

Foxeer Razer model Mini front camera (optional)

TX526 FPV Video Transmitter

2 esc for the motors I put 90A but 70A is enough

2 lipo 3S 6000mah

have fun!

This work is licensed under the Creative Commons Attribution - Noncommercial - Nonmodification 4.0 International License. To view a copy of this license, visit

3D printing settings

print on

CR10S PRO V1 nozzle of 0.6 layer height 0.3 100% filling for the whole hull ( all 12 parts )

and ENDER3 V2 nozzle of 0.4 layer height 0.2 100% filling for almost all the parts

3D printer file information

  • 3D design format: STL Folder details Close
    • Boitier Largue ligne.stl
    • Capuchon moletage M6.stl
    • Coque AVG Sup.stl
    • Coque ARD Inf.stl
    • Coque ARD Sup.stl
    • Coque ARG Inf.stl
    • Coque ARG Sup.stl
    • Coque AVD Inf.stl
    • Coque AVD Sup.stl
    • Coque AVG Inf.stl
    • Coque MilieuD Inf.stl
    • Coque MilieuD Sup.stl
    • Coque MilieuG Inf.stl
    • Coque MilieuG Sup.stl
    • Couvercle Largue ligne.stl
    • Couvercle bac 1 et deux .stl
    • Couvercle roulement bac1.stl
    • Cremaillere largue ligne.stl
    • Crochet bac 2.stl
    • Enjoliver testeur de tension.stl
    • Enjoliveur inter.stl
    • Enjoliveur led Av support cam.stl
    • Entretoise 0.3.stl
    • Entretoise 0.5mm.stl
    • Entretoise 1mm.stl
    • Entretoise largue ligne.stl
    • Envoliveur led Ar.stl
    • Envoliveur led Av simple.stl
    • Envoliveur led.stl
    • Gabarit feu Ar.stl
    • Gabarit percage Led AV.stl
    • Insert poignee cote D.stl
    • Insert poignee cote G.stl
    • Logement barre de capot.stl
    • Moletage M6.stl
    • PLATINE SERVOS v1.stl
    • POULIE TREUIL Malle.stl
    • Pignon Largue ligne.stl
    • Platine servo bac 1 et 2.stl
    • Poignee de transport.stl
    • Porte bac 2.stl
    • REHAUSSE BAC.stl
    • Tuyere v2.stl
    • VIS V3 part1.stl
    • VIS V3 part2.stl
    • barre de capot part1.stl
    • barre de capot part2.stl
    • barre de capot part3.stl
    • barre de capot part4.stl
    • boitier bac 1 vis sans fin.stl
    • boitier bac2.stl
    • boitier servos bac 1 et 2.stl
    • cache xt60 gx16 D .stl
    • cache xt60 gx16 G .stl
    • cam foxeer.stl
    • demi lune 1.stl
    • demi lune 2.stl
    • inter cache.stl
    • platine D TREUIL .stl
    • platine G TRUIL .stl
    • support batterie DR.stl
    • support de baterrie G.stl
    • support moteur DR.stl
    • support moteur G .stl
    • support tube X4.stl
    • vis sans fin V2.stl
  • Last update: 2021/06/20 at 15:31
  • Publication date: 2021/01/08 at 10:27





Page translated by automatic translation. See the original version.
Issue with this design? Report a problem

Best sellers of the category Various

Add a comment


et'il possible realiser ce bateau avec une ender 3 max ?

Oui sans problème . Aucune pièces ne dépassera les 340mm de ender3 max

hello. no sorry, only STL files are provided

Hi, I am really interesting in your model, considering to purchase it but would like to know do you provide source of CAD files which could be needed to customise it or just STL files?

ok thanks for the answer we gone buy the stl can you tell us the best fillament for printing please?

I did not count the hours but I think about a hundred hour of printing

hi can you tell us howmany huor printing please

Faut pas le faire imprimer ça ne sera pas rentable du tout. Il faut avoir une imprimante

Merci pour ta réponse. Connais un site en ligne pour imprimer tout ça ? Quel est le coût de revient de l'impression ?

Salut. Les différentes parties s assemble grasse a une collerette sur toute les parties de la coque et se colle au sika11fc .
Il n y a pas de trou prévu pour une sonde mais vous pouvez toujours la percer pour en mettre une je ne pense pas que se soit difficile à faire .
Je bac a une contenance correct je pense. J ai pas les moyens de mettre 1 kilos de bouillette sur chaque cannes. Lol

Derniere question, Il y a un emplacement prévu pour mettre la sonde d'un écho ? j'ai pas l'impression en regardant le dessous :(

Avec quoi il faut coller les différente partie de la coque ? merci

Beau boulot ! Un bac d'amorcage un peu plus grand aurait été top !

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon or Aliexpress.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!