Skip to content

Hi naughty one! So you'd like to have fun with kinky 3D printed models?! You are right ;)

But on Cults, little bunnies have to prove they are grown up enough.

Stroker Holder v1 (3D-Printable Sexercise Doll)

?
Creation's quality: 5.0/5 (2 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 22.4k views
  • 38 likes
  • 23 downloads

3D model description

Do you have a large format 3D Printer? Looking for a better way to stay healthy, in shape and exercise not just one hand? Finding those flesh-toys (ex. pocket pussies, fifis, male masturbators, strokers and silicone vaginas) un-immersive and not motivating enough for "the little fireman"?

3d-print this model and enjoy great workouts with this awesome and useful apparatus. Introducing the Stroker Holder v1, a deliberate rigid body design for folks looking to improve their health, their "hard drives" and/or simply experience flesh toys in new and fun ways.

The body is 29x29x38cm (11x11x15 inches) in size with a cavity that is 20cm (8in.) deep. The removable 2-piece cylinder is 9.5cm (3.7in) in diameter and fastens into the cavity via a twist-fasten mechanism¹.

The 2-piece removable cylinder design enables customization of content density allowing the compression of soft content such as, roll-up cloths, sponges, silicone flesh-toys, water baloons, etc. by joining the adapter cap (shaped like the buttocks) with the container cup together (also twist-fastened).

The removeable cylinder is then slided into, and twist-fastened into the body cavity. This simple design also allows for quick and easy hygiene by sliding out only the parts that need cleaning.

BENEFITS

  1. Promotes full exercise of pelvic, abdominal and upper-body. Not just one hand/arm.
  2. Greater exercise that can reach cardiovascular levels.
  3. Rigid body allows partial dress-up.
  4. Increases pelvic-banging sensation due to rigid surface.
  5. Customizable perimeter wall and infills increases durability allowing for rougher treatment.
  6. Print using your favorite color and rigid filament material.
  7. Easy to clean / maintain.
  8. Very light weight (approx. 0.8kg or 1.7lb)

Feel free to leave comments and suggestions (size, poses etc.) for v2 (development in progress).

¹ Add thickness to the removable cylinder with masking tape for a tight, smooth and quiet fit inside the cavity.

3D printing settings

GENERAL (CURA) SETTINGS

QUALITY
Layer Height: 0.2mm
Line Width: 0.4mm
- Skirt/Brim Line Width: 0.4mm

SHELL
Wall Thickness: 0.8mm (minimum 2 perimeter walls)
Top/Bottom thickness: 0.8mm
- Top Layers: 4
- Bottom Layers: 2
Top/Bottom Pattern: Zig Zag
Bottom Pattern Initial Layer: Zig Zag
Optimize Wall Printing Order: True (checkmarked)
Fill Gaps Between Walls: Everywhere

INFILL
Infill Density: 10-15% (The more the better)
- Infill Line Distance: 10mm
Infill Pattern: Zig Zag (or grid but always same angle)
Infill Overlap Percentage: 20%
Infill Layer Thickness: 0.2mm
Gradual Infill Steps: 0

MATERIAL (PLA)
Printing Temperature: 195°C
Printing Temperature Initial Layer: 200°C
Default Build Plate Temperature: 60°C
Build Plate Temperature: 60°C
Build Plate Temperature Initial Layer: 70°C
Diameter: 1.75mm (PLA)
Flow: 100%
Initial Layer Flow: 110%
Enable Retraction: True
Retraction Distance: 8mm
Retraction Speed: 60mm/s
Retraction Minimum Travel: 1.5mm

SPEED
Print Speed: 65mm/s
Travel Speed: 85mm/s
Print Jerk: 2mm/s
Travel Jerk: 2mm/s

Generate Support: True
Support Placement: Touching Buildplate
Support Overhang Angle: 75°
Support Pattern: Zig Zag

BUILD PLATE ADHESION (only for priming the nozzle)
Build Plate Adhesion Type: Skirt
Skirt Line Count: 2
Skirt Distance: 0.5mm

  • Your settings may vary based on room temperature and how well your 3D printer is calibrated.

PRINT TIME:
Body: Approximately 35-50hrs (depends)
Adapter Cap: 4-5hrs.
Container Cup: 3-4hrs.

These times are baselines and based on the above settings plus printer performance. Actual print time may vary.

  • 3D file format: STL
  • Last update: 2019/02/17 at 12:28
  • Publication date: 2018/07/31 at 12:57

Tags

Creator

Designs 3
Downloads 49
Sales US$1,217
Followers 34

Copyright

©


Best sellers of the category Naughties


Add a comment

2 comments

Another person asked less than a week ago. So, I'm now planning to do an original size but cut up for smaller print beds. I'm targetting 220x220x250 which is the Ender 3 I believe. Is that good for you too?

Is there any way you could cut this up so it could fit on smaller printers?


Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon, Gearbest or Aliexpress.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!