Skip to content

Mechanical universal telephone holder - Mechanical universal telephone holder

?
Creation's quality: 4.0/5 (27 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 45.7k views
  • 283 likes
  • 421 downloads

3D model description

This is a universal phone holder that allows you to hold your phone horizontally and vertically. Ideal for supporting your phone at the desk or on your bedside table. What could be better than not holding your phone while you watch a show. It also allows you to charge your phone in both positions. It fits any type of phone, just set it to your own. It supports phones up to 160mm long (horizontal position) and 47mm wide minimum (vertical position). In particular, it allows you to tilt the phone's viewing angle according to your position. The quick lock/unlock mechanism is based on the phenomenon of gravity. When you let go of your phone, the mechanism locks it and when you grasp your phone, the mechanism releases it. All components are printable, you only need a small rubber band. A PDF file in French and in English (Tutorial) will guide you throughout your realization (Printing parameters, Assembly, ...) and I remain available to answer all your comments.

3D file format: STL

Update (15/06/2020): Some have complained of foot weakness. I have just added files with the name V2 which is a reinforced version.

This is a universal phone holder that allows you to hold your phone horizontally and vertically. Ideal for supporting your phone in the office or on your bedside table. What could be better than not holding your phone while you watch a series. It also allows you to charge your phone in both positions. It fits any type of phone, just set it to your own.

It supports phones up to 160mm long (horizontal position) and 47mm wide minimum (vertical position). In particular, it allows you to tilt the phone's viewing angle according to your position. The quick lock/unlock mechanism is based on the phenomenon of gravity. When you let go of your phone, the mechanism locks it and when you grasp your phone, the mechanism releases it. All the components are printable, you only need a small rubber band. A PDF file in English and French (Tutorial) will guide you throughout your realization (Printing parameters, Assembly,...) and I remain available to answer all your comments.

3D file format: STL

Update (15/06/2020): Some people have complained of a weakness in the foot. I just added files with the name V2 which is a reinforced version.


3D printing settings

12 Components to be printed

Layer height: 0.2 mm

Nozzle: 0.4 mm

Filament: PLA 1.75mm

Printing temperature: 200°C

Tray temperature: 60°C

All other settings are available in the PDF file.

12 Components to be printed

Layer height: 0.2 mm

Nozzle: 0.4 mm

Filament: PLA 1.75mm

Printing temperature: 200°C

Build plate temperature : 60°C

All other settings are available in the PDF file.

3D printer file information

  • 3D design format: PDF and STL Folder details Close
    • Axe - Axis.stl
    • Bati - Frame.stl
    • Bati V2 - Frame V2.stl
    • Bras - Arm.stl
    • Circlip - Snap ring.stl
    • Cremaillere - Rack.stl
    • Cremaillere 2 - Rack 2.stl
    • Ecrou M8 - Bolt M8.stl
    • Engrenage - Gear.stl
    • Pied - Foot.stl
    • Pied 2 - Foot 2.stl
    • Pied 2 V2 - Foot 2 V2.stl
    • Pied V2 - Foot V2.stl
    • Teton.stl
    • Tutoriel Support téléphone - Tutorial Phone holder.pdf
    • Vis M8x19 - Screw M8x19.stl
  • Last update: 2020/06/15 at 19:44
  • Publication date: 2020/04/18 at 13:52

Copyright

©

Tags

Creator

Designs 9
Downloads 472
Sales US$1,334
Followers 43

Hello everyone !

I'm a mechanical designer in France with a degree in engineering. Do not hesitate to contact me if you have any questions about my files.
Have a good print. 👍

Page translated by automatic translation. See the original version.
Issue with this design? Report a problem

Best sellers of the category Gadget


Add a comment

8 comments

Hello. Thank you very much. This is my own design.

I like it! I haven't seen a stand like this before, is it similar to another or totally new and your original design? Just curious, thanks!

las tuercas no roscan, que puedo hacer?

I just finished my first make of this. I like the design, but I'm going to reprint with less horizontal expansion. The parts all fitted too loose. I had trouble with the gears and the racks being sloppy and the bolts and nuts would not tighten enough to keep the holder upright

Overall, a very nice design. However, there are too many parts (the holes at the top of the foot and the guides on the frame) that rely on layer to layer strength. These are high stress areas and should be redesigned, or default printing orientation adjusted, so the layer adhesion is not a factor.

Un énorme merci pour l'update, effectivement il y a de gros changement :)

Bonjour F3N3K. Désolé pour ce problème. Je viens d'ajouter des fichiers avec la dénomination V2 qui est une version renforcée.

Casse facilement au niveau de l'axe de rotation du pied mais le reste fonctionne parfaitement. Vraiment dommage.


Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon or Aliexpress.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!