Skip to content

Motorized Halloween Pumpkin Bracelet

3D model description

UPDATES:

1) A lighted version of this thing is here: http://www.thingiverse.com/thing:1784381.

Have you been searching in vain for an animated Halloween pumpkin bracelet for the upcoming Halloween parties (and who isn't)? Well Motorized Halloween Pumpkin Bracelet might be the Thingiverse thing for you!

Motorized Halloween Pumpkin Bracelet includes two bracelet styles. The first is a rigid bracelet style that can, with moderate heating from a handheld hairdryer, be slightly adjusted to wrap around the wrist. The second is a watch strap style and is designed for a 19mm wide by 3mm thick one piece velcro watch strap. This style accommodates more wrist sizes.

In both styles, a 6vdc battery pack (4 1.5vdc AA cells with on/off switch) is wired to the motor with enough wire to fit up a sleeve and into a pocket. A newer version will follow with on board batteries.

Video of prototype Motorized Halloween Pumpkin Bracelet in vise is here: https://www.youtube.com/watch?v=ubg8rI712io.

Video of prototype Motorized Halloween Pumpkin Bracelet on my wrist is here: https://www.youtube.com/watch?v=ADwiCzazJRs.

Designed using Sketchup Make 2016 and printed in PLA on an Ultimaker 2 Extended.

3D printing settings

Printer Brand:

Ultimaker

Printer:

Ultimaker 2

Rafts:

No

Resolution:

.1mm

Infill:

20

Notes:
When printing "Gear Crown.stl", supports may be required.

Post-Printing
Parts I Purchased:

1) Gear Motor: DC 6V 60 RPM High Torque Electric Replacement Gear Box Motor (Amazon).

2) Battery Holder: Plastic On/Off Switch 4 x 1.5V AA Battery Case Holder w Cap Black (Amazon).

3) Batteries: 4 AA batteries.

4) Velcro one piece watch band (19mm wide, 3mm thick) (Walmart).

5) 26 gauge red stranded wire.

6) 26 gauge black stranded wire.

Printing:

Print 2 "Pin.stl". Print 1 of either "Bracelet.stl" or "Bracelet Strap.stl". Print 1 each of the remaining pieces.

When printing "Gear Crown.stl", supports may be required depending on your printer, printer settings and color.

Assembly:

Prior to assembly, test fit and trim, file, sand, etc. all parts as necessary for smooth movement of moving surfaces, and tight fit for non moving surfaces. Depending on the colors you chose and your printer settings, more or less trimming, filing and/or sanding will be required. If the tight fitting components are too loose, add a small dot of cyanoacrylate to each side of the pin, allow to dry completely (I use accelerator to speed the process), then try the fit again. Repeat until tight.

Assemble as per "Assembly.stl". I perform the assembly task in the following order:

1) Press "Gear Motor.stl" onto the motor.

2) Slide the motor & gear assembly into "Bracelet.stl".

3) Press two "Pin.stl" into "Gear Crown.stl".

4) Using "Axle.stl", attach the gear crown assembly to "Bracelet.stl". The gear crown assembly should rotate freely on the axle.

5) Attach "Base Pumpkin.stl" to the gear crown assembly by sliding the pin heads into the large holes in "Base Pumpkin.stl", then rotating "Base Pumpkin.stl" counter clockwise (as viewed from the top) to secure it in place on the gear crown assembly.

6) Press "Stem Pumpkin.stl" into "Lid Pumpkin.stl".

7) Attach the lid assembly to "Base Pumpkin.stl".

8) Solder the battery holder positive (red) terminal to the motor positive terminal, with extension as required to reach from a pocket to the bracelet. Solder the battery holder negative (black) terminal to the motor negative terminal, also with extension as required to reach from a pocket to the bracelet.

Place the assembly on your wrist and turn it on. Hope you make one!

  • 3D model format: STL

Tags

Creator

Designs 223
Downloads 11782
Followers

The more mistakes I make, the more knowledge I gain.

License

CC BY NC

Best sellers of the category Gadget

Related contents


Add a comment


Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon, Gearbest, Banggood, Aliexpress or Ebay.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!