Please note: This is an adapted version of my Raspberry Pi 3 case (https://cults3d.com/en/3d-model/various/malolo-s-screw-less-snap-fit-raspberry-pi-3-model-b-case-stands) that I modified to fit the Raspberry Pi 4. I do not yet own the Raspberry Pi 4 myself. However Thingiverse user Haz1 (https://www.thingiverse.com/Haz1/about) was kind enough to patiently print several iterations of the case and send me pictures to check the fit. Thank you Sebastian :-).
Since I did not yet print this thing the pictures only consist of a few renders. If you want to see how it will look printed please have a look at the Raspberry Pi 3 version (https://cults3d.com/en/3d-model/various/malolo-s-screw-less-snap-fit-raspberry-pi-3-model-b-case-stands). It's the identical case but with a few differences due to the different board layout of the Raspberry Pi 3 .
There already is a plethora of raspberry pi cases on the internet and the last thing we need is yet another one ... well - I created one anyway ... because I wanted to and I had a lot of fun doing it :-).
I tried to achieve the following key features:
* Easy to print without support (no steep overhangs or long bridges and stuff).
* Top and bottom layer printable on print surface (so I could make good use of my recently acquired awesome powder-coated/textured print sheet).
* No screws or glue needed (snap fit).
* Slim/compact outline.
* Acceptable ventilation without fan.
* Good looking (very subjective - I know).
* I also wanted a stand to put it on.
I tested the Raspberry Pi 3 version with 0.2mm and 0.1mm layer height. Both worked well so this settings will also work for the Pi 4 version. I would recommend to use PETG for better heat resistance.
If you have any questions, suggestions or requests don't hesitate to let me know.
There are several different designs for top and bottom
There are three different stands
The vertical one also has a version that routs the Rasberry Pi status leds to the front. To achieve this you have to print the file "Stand_Vertical_LED_Guide.stl" twice using a transparent filament and slide it into the according holes of file "Stand_Vertical_LED.stl". It's difficult to explain - just have a look at the pictures.
I don't have a multi material printer but learned that you can create a multi material print pretty easily without special hardware (as long as the multi material part does not span over to may layers - otherwise it gets a pita). By multi material I don't mean switching filament at certain layers (which would not have worked in my case because I wanted the top and bottom layers to be on the print surface) but a true multi color print (as seen in the pictures). Here is a short instruction of how it works:
I used Prusa Slicer for this but I guess it would work with the original Slic3r in a similar way
Whenever your printer reaches the M600 command it will pause outside the print area and prompt you to switch filament (supposedly your printer supports the M600 G-code command).
This all probably sounds more complicated then it is. Once you understood how it works it's actually pretty straight forward.
There are quite a few different versions of STL files. There are different designs and for each design there are different options with regards to slots for camera and display cables and an access slot to the pins. To help you pick the right files I used the following naming scheme:
If you are unsure which file to pick just open it in your slicer and see what it looks like.
You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:
ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.
DONATE: If you want, you can make a donation via PayPal here.
WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!