Skip to content

It's 'not' too late - Original art by Bram Tan, (Big print! Not for the faint hearted).

3D model description

https://youtu.be/C7u6LmDyUGQ

You can now print one of my original works. Have fun!

This is a piece of art I made when I was thinking about my life and goals. At the time I was also fascinated by Dr. Ishihara's colorblindness tests for their colour and simplicity. In the end I realised that whether it might be 'too late' or it might 'not' be too late, all depends on my personal vision! What do you see when you look at these paintings.

By using my 3D printed woodblock Ukiyo-e technique, you can print as many different colour versions as you like depending on how you want to answer this question. Whichever it is, I promise you are going to be much more relaxed about it afterwards!

Detailed PDF instructions on how to use these plates are included in this download

For this particular design, you will need a large wooden board to stick the plates and paper onto, and draw a vertical and horizontal center-line in pencil as center guides for the plate positioning.

This design is a large portrait print for a paper size of approximately 700mm wide x 700mm tall, but I recommend slightly larger paper size in order to have a border. It consists of 6 'woodblocks' which are made from 2-4 x 3D printed panels each. There are 22 plates in total, each panel must be taped together with gaffer tape to make one 'woodblock'(see example pic), hence you will have 6 full sized plates/6 different colours. You can refer to my finished image or even the original for a colour reference but choose your own colours by all means.

Sometimes the files are named with the suffix 'top' and 'bottom' to help you figure out which ones to tape together sometimes A,B and C etc. I have also included instructions about which plates need to be used first and last, sometimes I number all the files to show the full order in which they should be used, this is so that when you start printing with paint you don't get a strong layer of colour hiding the layers beneath it.

The plates will last for many many prints and if you use acrylic which dries in a few minutes, you don't have to wash the first layer of old paint off, in fact the surface gets a bit better after one layer of old paint has dried onto it, but you should wash paint off from subsequent print sessions to avoid build-up. I usually place them in soapy water and wash them all together only when I'm done with the session.

More info at https://bramtan.weebly.com/developing-3d-printed-ukiyo-e.html

More designs to come. Enjoy!

3D printing settings

3D Print settings: I personally use 0.6mm nozzle and a 0.3mm layer for speed, but the regular 0.4mm nozzle with a 0.2mm layer will give you even better detail but takes longer. The prints generally require a 300mm x 300mm print size, if your 3D printer is smaller then just scale the plates down. But only scale in the X and Y directions, not the Z, you must maintain the same thickness. This is important for the ukiyo-e printing technique to work properly. Use printer settings that create 100% solids rather than honeycomb inside, the results will be better. Don't just set 100% infill setting to achieve a solid print. This will normally make the 3D printer do long stretches of print head zigzagging while it tries to do a very fine honeycomb structure, this causes lots of vibrations and noise. Instead, by specifying a high enough number for the 'top/bottom infill layers', higher than the number of actual layers required to print the panel, the printer is forced to do a more efficient back and forth movement pattern (just like it does for normal bottom and top layers) for every single layer, resulting in a better version of 100% infill, with smoother movement and less vibes.

After printing each plate, use a sanding block and 120+ grit sandpaper to make the top surface really flat so it holds paint evenly. This does not take long if you have used PLA plastic, since it is quite soft. Note: The solid strip of plastic at the top does not need sanding, it is there for you to attach your paper using masking tape - see my instruction PDF called 'The Kit'.

  • 3D file format: PDF and STL

Tags

Creator

Designs 19
Downloads 188
Followers

Dear Cults and Friends,

Thankyou for featuring my work this month! Now it will be a memorable month for more than just this crazy (but very necessary) lock-down. In the face of the pandemic, 3D printing is showing off its awesomeness all around the world, making emergency parts for hospitals as well as keeping us entertained at home. I'm proud to be part of it. Brilliant!

Merci Cults! Je suis très honoré.

I spent my childhood taking things apart to see how they worked, then I discovered design and started putting things together, now I am an artist and industrial designer.

I only started 3D printing in 2016 and I've learned a lot since, I now prototype various designs of experimental 3D printers and also developing a form of modern 3D printed Ukiyo-e woodblock printing.

Since we are on lock-down here in France, I've been using my time to upload more 3D printed Ukiyo-e 'woodblocks' to Cults, the ones for beginners are free. Try it out and enjoy making something simple beautiful with your mind and hands.

This short video introduces my process - https://youtu.be/C7u6LmDyUGQ

Enjoy!

Bram Tan aka Printer With Attitude

Copyright

©

Best sellers of the category Art

Related contents


Add a comment


Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon, Gearbest, Banggood, Aliexpress or Ebay.

  • DONATE: If you want, you can make a donation via PayPal here.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!