Zum Inhalt gehen

Red Squirrel Compact Fan Housing - Ender 3 Pro - 5015 Rev1

?
Qualität der Kreation: 5,0/5 (3 Stimmen)
Bewertung von Mitgliedern zu Druckbarkeit, Nützlichkeit, Detailgrad usw.

Beschreibung des 3D-Modells

This is a new design! If you make one please post a make and provide feedback!
Based on feedback and my own use I've made some tweaks and uploaded Rev1. Nothing critical, just continuous improvement stuff. Rev1 notes are at the bottom.

Also, I have no idea why the file previews aren't working on thingiverse?

I designed this housing after I got a CR-10 V2 and really liked the cooling fan housing that comes on it. I had been using a Hero Me single 5015 with good results, but wanted something a little more compact. This design is about 8mm smaller in the X and Y axis. It uses smaller 3x10mm air ports to create higher velocity air directed right at the base of the nozzle. I tested the flow from each port using a flow meter and it is exactly the same on each port so there should be good symmetrical part cooling.

This design is also very inspired by the Hero Me, in fact you will need the HM_Base_Lock_No_ABL to install it. It is compatible with the various ABL sensor mounts for Hero Me. I have printed them and tested the fit however I do not use ABL so I cannot test them. Get the stuff you need here: https://www.thingiverse.com/thing:3182917
ABL offsets should be the same as Hero Me recommends since the sensor and nozzle are in the same positions (please correct me if I'm wrong)

Print the main section with the back side down, 40x40 hot end cooling fan face up. You will need supports, touching buildplate only. If you use supports everywhere they will fill the air ducts with support and they won't work! I used .2 layers, 3 walls, 1.2mm top and bottom and 20% infill.

Print the clamp flat on the bed with the groove down and pin up. No supports needed. I used .2 layers and 4 or 5 walls for extra strength.

The fan guard is something I drew up quick but I like it. It just presses in place. Print face down. Be careful removing it from the bed, too much adhesion and it will be ruined. It is nice and quiet though.

NEW 3/28/20-Added the 4010 blower adapter so you can now use your stock fan with this unit! However I haven't tried it... so if you do, please let me know how it works :)
-you probably will want to print it standing up with supports.

Rev1 updates...
- Made some tweaks to the area where the Hero Me parts interface. They fit better now and the flange is a little thinner so the screws will have more threads into the plate behind the duct.
- Added vent holes to the left side of the duct to improve cooling air flow and try to reduce the amount of air blowing down below the duct. You still want some airflow down there to keep the duct from warping.
- Increased the height of the groove on where fan wires are routed.
- Added some material to the front 5015 fan mount
- Added a longer boss for the rear 5015 fan mount with a hole for optional #4-40 or 3mm screw. (I don't use one)
- Added optional Red Squirrel logo fan guard :)
- Tweaked screw fits and clearances on the duct and clamp.

Informationen zur 3D-Druckerdatei

  • Format der Gestaltung 3D: STEPundSTL Datei-Details Schließen
    • RS_Fan-Housing-Clamp-Rev1.step
    • RS_Fan-Housing-Clamp-Rev1.stl
    • RS_Fan-Housing-Duct-Rev1.step
    • RS_Fan-Housing_-_Clamp.stl
    • RS_Fan-Housing_-_Duct.stl
    • RS_Fan-Housing_-_Guard.stl
    • RS_Fan-Housing_clamp.step
    • RS_Fan-Housing_guard_logo.stl
    • RS_Fan_Housing_4010_Adapt-Rev1.stl
    • RS_Fan_Housing_Duct.step
    • RS_Fan_Housing_Duct_Rev1.stl

    Mehr zu den Formaten

  • Veröffentlichungsdatum: 2020-04-03 15:42
    ?
    Veröffentlicht auf Thingiverse am: 2020-02-19 04:23

Lizenz

CC BY NC

Keywords

Creator

Seite mithilfe von automatischer Übersetzung übersetzt. Originalversion ansehen
Problem mit diesem Design? Ein Problem melden

Bestseller der Kategorie Werkzeuge


Kommentar hinzufügen

2 Kommentare


Möchtest du Cults unterstützen?

Gefällt dir Cults und möchtest du uns dabei helfen,das Abenteuer in völliger Unabhängigkeit fortzusetzen? Beachte, dass wir ein kleines Team von 3 Personen sind und dass es daher sehr einfach ist, uns dabei zu unterstützen, weiterhin im Geschäft zu bleiben und zukünftige Entwicklungen zu schaffen. Hier sind vier Lösungen, die allen zugänglich sind:

  • WERBUNG: Deaktiviere deinen Adblocker und klicke auf unsere Werbebanner.

  • MITGLIEDSCHAFT: Führe deine Onlineeinkäufe durch, indem du auf hier auf die uns zugehörigen Links bei Amazon oder Aliexpress klickst.

  • SPENDE: Wenn du möchtest, hast du die Möglichkeit, uns hier über PayPal eine Spende zukommen zu lassen.

  • MUND-ZU-MUND-PROPAGANDA: Lade deine Freunde dazu ein, die Website und die großartigen 3D-Dateien kennenzulernen, die von der Community geteilt werden!