Zum Inhalt gehen

C-Clamp / G-Clamp 01 - 03

?
Qualität der Kreation: 3,8/5 (6 Stimmen)
Bewertung von Mitgliedern zu Druckbarkeit, Nützlichkeit, Detailgrad usw.
  • 👁 8,4k Aufrufs
  • 49 Likes
  • 1k herunterladens

Beschreibung des 3D-Modells

I've created this C-Clamp (or G-Clamp if you like to call it this way) because of three reasons.

1) For my upcoming enclosure build I'll need some clamps to hold parts together.
2) To train my Fusion 360 skills
3) I've never printed threads on my (new) 3D printer. So it was a good way to tests what threats are easy to print an working reasonable well.

As usual I've attached the Fusion 360 file to make adjustments easier for you. You will also find a factory file with the settings from my Prusa MKS2 and PLA from Das Filament.

During the design phase I used this https://goo.gl/YcnZ7b to test various threads, diameter, offset etc. combination to find a good working and printable thread. Perhaps it's a good idea to print this first to test if the combination is suitable for your printer, too. Also it migth a good starting point for your own thread tests.

Side note: I'm new to 3D printing and I've to learn everything. I believe that making things on your own from the very first step is harder but finally you will get things done. Because of that I try not to download lot of things but create them from scratch. Even if they already exists. By sharing those things I hope to get feedback that I can improve my skills. So don't be angry if I upload things which already exists here.

Update 2017/09/04: Link to thread test (https://goo.gl/YcnZ7b) added
Update 2017/08/09: You're preferring screw clamps? Try this (https://goo.gl/LvzV1z).
Update 2017/08/02: Based on the feedback from @wavapps I've added to additional versions of the C-Clamp

C-Clamp 01 (red"C"): Unchanged
C-Clamp 02 (yellow "C"): Like @waveapps I wasn't sure about the retainers of the shoe. Now they are about 3 times thicker. I haven't printed them yet because my printer is busy, but unless the gaps didn't change everything should still work. @wavapps reported a slight bending on the lower part of the clamp so I've added a cut out to the lower part of the "C" with half of the depth of the original cut outs. I haven't done this initially because I was afraid of to thin walls or screws but this might be a good compromise.
C-Clamp 03 (blue "C"):Thicker retainers like for clamp 02 (but all the shoes are interchangeable) and a full depth cut out on the lower part of the "C" Because of the cut out the depth is now slightly bigger.


3D-Druckeinstellungen

Printer Brand: Prusa
Printer: Prusa Mk2
Resolution: 0.2
Infill: 30%

Notes:

For my first (and currently only) print I've used 8 shells, top and bottom layers. Perhaps to much. I don't know.

You might want to add some support below the cut outs of the "C" if you print it lying on the bed.

Informationen zur 3D-Druckerdatei

  • Format der Gestaltung 3D: F3DundSTL Datei-Details Schließen
    • C-Clamp_01_v20_C-Clamp_01_v20_C_1_C_C.stl
    • C-Clamp_01_v20_C-Clamp_01_v20_Stamp_1_Platform_Stamp.stl
    • C-Clamp_01_v20_C-Clamp_01_v20_Stamp_1_Stamp_Stamp.stl
    • C-Clamp_01_v22.f3d
    • C-Clamp_02_v4.f3d
    • C-Clamp_02_v4_C-Clamp_02_v4_C_1_C_C.stl
    • C-Clamp_02_v4_C-Clamp_02_v4_Stamp_1_Platform_Stamp.stl
    • C-Clamp_02_v4_C-Clamp_02_v4_Stamp_1_Stamp_Stamp.stl
    • C-Clamp_03_v2.f3d
    • C-Clamp_03_v2_C-Clamp_03_v2_C_1_C_C.stl
    • C-Clamp_03_v2_C-Clamp_03_v2_Stamp_1_Platform_Stamp.stl
    • C-Clamp_03_v2_C-Clamp_03_v2_Stamp_1_Stamp_Stamp.stl

    Mehr zu den Formaten

  • Veröffentlichungsdatum: 2019/11/25 19:35

Lizenz

CC BY

Keywords

Creator

Seite mithilfe von automatischer Übersetzung übersetzt. Originalversion ansehen
Problem mit diesem Design? Ein Problem melden

Bestseller der Kategorie Werkzeuge


Kommentar hinzufügen


Möchtest du Cults unterstützen?

Gefällt dir Cults und möchtest du uns dabei helfen,das Abenteuer in völliger Unabhängigkeit fortzusetzen? Beachte, dass wir ein kleines Team von 3 Personen sind und dass es daher sehr einfach ist, uns dabei zu unterstützen, weiterhin im Geschäft zu bleiben und zukünftige Entwicklungen zu schaffen. Hier sind vier Lösungen, die allen zugänglich sind:

  • WERBUNG: Deaktiviere deinen Adblocker und klicke auf unsere Werbebanner.

  • MITGLIEDSCHAFT: Führe deine Onlineeinkäufe durch, indem du auf hier auf die uns zugehörigen Links bei Amazon oder Aliexpress klickst.

  • SPENDE: Wenn du möchtest, hast du die Möglichkeit, uns hier über PayPal eine Spende zukommen zu lassen.

  • MUND-ZU-MUND-PROPAGANDA: Lade deine Freunde dazu ein, die Website und die großartigen 3D-Dateien kennenzulernen, die von der Community geteilt werden!