Zum Inhalt gehen

Covid-19 Protection Face Mask / Face splash mask

?
Qualität der Kreation: 5,0/5 (1 abstimmen)
Bewertung von Mitgliedern zu Druckbarkeit, Nützlichkeit, Detailgrad usw.
  • 👁 5,7k Aufrufs
  • 3 Likes
  • 280 herunterladens

Beschreibung des 3D-Modells

Mask design for use by healthcare personnel primarily for splash protection of patients with covid-19 or suspected virus.

This design has been modified, prototyped and validated several times during the last 3 weeks from (23/March/2020) until a final version was obtained thanks to the joint work with health personnel who gave us their appreciation and recommendations for the improvement of the designs. These elements were exposed to disinfection methods in different medical institutions in the city of Popayán - Colombia, giving good results.

It is important to clarify that the accessories are called contingency and must be used in the event of a shortage of medical supplies. Our recommendation is that these accessories be treated as DISPOSABLE.

In response to the current emergency caused by the spread of the new coronavirus, a group of Makers, businessmen, students, teachers and citizens met to seek to contribute to the vast needs that our society is going through these days and that is how, from our knowledge, we have developed these "contingency accessories for the protection of health personnel who are exposed every day to a possible contagion of Covid-19.

The disinfection tests that have been validated so far have been with the following elements by health personnel:

-Virucide Disinfectant VIRKON™ S.

-KLORKLEEN disinfectant.

The following have been used by the manufacturers (MAKERS) for disinfection methods:

-Mixture of CHLORINE and water in a 1/10 proportion.

-White vinegar.

-Water and soap.

MATERIALS USED FOR ASSEMBLY:

-Covid-19 Anti-Sappice Caretaker.

-30x26cm Acetate sheet, recommended to be #8 or #10 caliber... if you can't find this caliber you can also use the acetate that is sold in letter size block.

-Spring or rubber, preferably a rubber that can be disinfected since the spring, having a disinfection process, usually wears out or is easily damaged.

*? Assembly steps ?

1- Print the 3d Covid-19 Face splash mask design.

2-Cut a sheet of acetate of 30x26 cm, recommended to be #8 or #10 gauge.

3-Assemble the acetate sheet with the 3D printing frame, make a small hole with a scalpel to the acetate in the blocks that are going to hold it, this for greater security that it does not move at any time.

4 - Enter and adjust the rubber or spring to fit the head of the person who will use this element.

3D PRINTING:

-0.26 layer height and 20% fill, 16 grams of material , 45 minutes to 1 hour 15 printing depending on the settings and printer to be used, printing speed: 80 to 110 mm/s.

We are the resistance, we are a new collaborative knowledge revolution.

Makers and entities that have contributed to the manufacturing processes of these masks to be donated in the city of Popayán: Darwin Manchola(SIS Popayán), Javier Adolfo Castillo(Celeste Team SAS), Jeison Sneider Ruiz Zemanate(Eureka! Technology & Uniautonoma del Cauca), Kevin Steven Castillo Solarte (3D Workshop Popayán), Iván Darío Martínez Martinez (3D Immersion), Carlos Andrés Arias Ramírez (FabLab FUP), Daniel Ararat Gomez (Unicomfacauca), Martin Muñoz (Semillero Robotica Unicauca), Ludwing Nicole Palomino Venachi(Telematics Department Unicauca)......

Makers Popayán and EurekaTechnology.

This design is a Remix, the original file is in the following link:

https://www.thingiverse.com/thing:4243158

Social networking:

-Makers Popayan Group:

https://www.facebook.com/MakersPopayan/

-Eureka! -4.0 technology:

https://www.facebook.com/3DEurekaTechnology/

-Link from the whatsapp group if you want to join the Makers Popayan movement:

https://chat.whatsapp.com/CXzbhascGU2JwxvR1YbRnh

-Web page:

http://eurekatechnologypopayan.com/

Mask design for use by health personnel mainly for protection against splashes of patients with covid-19 or suspected virus.

This design has been modified, prototyped and validated several times during the last 3 weeks from (23 / March / 2020) until we obtain a final version thanks to the joint work with health personnel who gave us their appreciation and recommendations for the improvement of the designs, these elements were exposed to disinfection methods in different medical institutions in the city of Popayán - Colombia, giving a good result.

It is important to clarify that the accessories are called contingency and must be

used before the shortage of medical supplies. Our recommendation is that these accessories be treated as AVAILABLE.

In response to the present emergency caused by the spread of the new

coronavirus a group of Makers, entrepreneurs, students, teachers and citizens us

we meet to find how to contribute to the vast needs that our society passes

these days and that is how from our knowledge we have elaborated these

"Contingency accessories for the protection of health personnel who are exposed

day by day to a possible contagion of Covid-19.

The disinfection tests that have been validated so far have been with the following elements by health personnel:

-VIRKON ™ S Virucidal Disinfectant.

-KLORKLEEN disinfectant

For the disinfection methods for manufacturers (MAKERS) the following have been used:

-Mix of CHLORINE and water in 1/10 ratio.

-White vinegar.

-Water and soap.

MATERIALS USED FOR THE ASSEMBLY:

-Covid-19 Anti-Splash Hatch.

-30x26cm Acetate Sheet, recommended to be # 8 or # 10 gauge ... if you can't find this gauge you can also use the acetate that is sold in letter size block.

-Spring or rubber, preferably a rubber that can be disinfected since the spring, having a disinfection process, usually wears out or is easily damaged.

3D PRINT:

-0.26 layer height and 20% filling, 16 grams of material, 45 minutes to 1 hour 15 of printing depending on the settings and printer to be used, printing speed: 80 to 110 mm / s.

We are the resistance, we are a new revolution in collaborative knowledge.

Makers and entities that have contributed to the manufacturing processes of these masks to be donated in the city of Popayán: Darwin Manchola (SIS Popayán), Javier Adolfo Castillo(Celeste Team SAS), Jeison Sneider Ruiz Zemanate (Eureka! Technology & Uniautonoma del Cauca) , Kevin Steven Castillo Solarte (3D Workshop Popayán), Iván Darío Martínez Martinez (Immersion 3D), Carlos Andrés Arias Ramírez (FabLab FUP), Daniel Ararat Gomez (Unicomfacauca), Martin Muñoz (Semillero Robotica Unicauca), Ludwing Nicole Palomino Venachi (Department Telematics Unicauca) .... Thank you all for being committed.

MakersPopayán and EurekaTechnology.

This design is a Remix, the original file is at the following link:

https://www.thingiverse.com/thing:4243158

Social networks:

-Popayán Makers Group:

https://www.facebook.com/MakersPopayan/

-Eureka! Technology 4.0:

https://www.facebook.com/3DEurekaTechnology/

-Link of the WhatsApp group if you want to join the Makers Popayán movement:

https://chat.whatsapp.com/CXzbhascGU2JwxvR1YbRnh

-Web page:

http://eurekatechnologypopayan.com/


3D-Druckeinstellungen

Printer brand:

Creality

Printer:

Ender 3

Rafts:

No

Supports:

Yes

Resolution:

0.26

Infill:

20%

Filament_brand:

ItMatters Filament - Colombia

Filament_color:

Yellow, Brown, Green

Filament_material:

PLA 1.75MM

Notes:

*0.26 layer height and 20% fill, 16 grams of material, 45 minutes to 1 hour 15 printing depending on the settings and printer to be used, printing speed: 80 to 110 mm/s *0.26 layer height and 20% filling, 16 grams of material, 45 minutes to 1 hour 15 of printing depending on the settings and printer to be used, printing speed: 80 to 110 mm / s.

Informationen zur 3D-Druckerdatei

  • Format der Gestaltung 3D: STL Datei-Details Schließen
    • CaretaEK_V1abierta.stl
    • CaretaEK_V2cerrada.stl

    Mehr zu den Formaten

  • Letzte Aktualisierung: 2020/04/24 06:57
  • Veröffentlichungsdatum: 2020/04/18 01:36

Lizenz

CC BY NC SA

Keywords

Creator

Somos una empresa de la ciudad de Popayán- Colombia dedicada a la comercialización de productos tecnológicos y componentes electrónicos, servicios de impresión 3D,Corte y grabado Láser, automatización y desarrollo de soluciones de Internet de las cosas IOT, Desarrolladores de hardware y software a la medida, soluciones basadas en tecnologías open source.

We are a company from the city of Popayán- Colombia dedicated to the commercialization of technological products and electronic components, 3D printing services, Laser cutting and engraving, automation and development of Internet of Things IOT solutions, Hardware and software developers tailored, solutions based on open source technologies.

Seite mithilfe von automatischer Übersetzung übersetzt. Originalversion ansehen
Problem mit diesem Design? Ein Problem melden

Kollektion im Zusammenhang mit diesem 3D-Modell


Bestseller der Kategorie Verschiedene


Kommentar hinzufügen


Möchtest du Cults unterstützen?

Gefällt dir Cults und möchtest du uns dabei helfen,das Abenteuer in völliger Unabhängigkeit fortzusetzen? Beachte, dass wir ein kleines Team von 3 Personen sind und dass es daher sehr einfach ist, uns dabei zu unterstützen, weiterhin im Geschäft zu bleiben und zukünftige Entwicklungen zu schaffen. Hier sind vier Lösungen, die allen zugänglich sind:

  • WERBUNG: Deaktiviere deinen Adblocker und klicke auf unsere Werbebanner.

  • MITGLIEDSCHAFT: Führe deine Onlineeinkäufe durch, indem du auf hier auf die uns zugehörigen Links bei Amazon oder Aliexpress klickst.

  • SPENDE: Wenn du möchtest, hast du die Möglichkeit, uns hier über PayPal eine Spende zukommen zu lassen.

  • MUND-ZU-MUND-PROPAGANDA: Lade deine Freunde dazu ein, die Website und die großartigen 3D-Dateien kennenzulernen, die von der Community geteilt werden!