23 Kommentare

There’s no reason they wouldn’t print with resin , I print them in Fdm , but designed not to need supports

Which STL , there are terms and conditions with this site that protect me, I’m more sure I would sell elsewhere

Этот нужен: https://cults3d.com/:1302960

What’s app +447777647037

Whats app +.44.77.77.647.037

That design pushes it left to avoid your purge bucket , I have to work in the office today , but give me a couple of days and I’ll adapt it for you if I’m able

Many thanks in advance for the revision of the design, however, as I said, it is less the proximity to the waste outlet but, as I said, the proximity to the rear upper cover, which is just too thick to attach the cover. In picture 3 you can see that the holes on the printer are located directly under the top cover.

On the original picture from the developer you can see it better because this cover is not transparent with him.

https://ibb.co/kMCQ13x

I understand what you are saying , and am just outlining the reasons for my design , which was designed before people started designing for the p1p which hadn’t been released. I designed to clear the shoot exit , to minimise the bend in the ptfe tubing exiting the base , and also to minimise visibility of the ptfe entering the device and minimising tube lengths which increase print times. I will take a look to see if can be plausibly altered whilst maintaining the design requirements for you.

Ok, thank you for taking care of my problem. Since a lot of people print a housing for this printer, I don't think I'm the only one with the problem because a lot of housings use the same or similar designs on the back.

Ive uploaded an additional one for you

Thanks for the revised file. The screw holes are now in the right place. Unfortunately, the hole on the right side (side with the Bambu Bus connections) has a smaller diameter. The hole on the left fits perfectly. https://ibb.co/ncgRDFB

Sorry I took a look and one of the recess sketches didn’t move , please examine the STL before printing in case I’ve missed anything, I just changed it , however I’m just off to work and it’s 5am , and I’m not fully awake

Thanks alot. For the super design and also for the quick revision so that it works with the Vision housing I used. It can't be any better than now. I'm super excited. When I got home from work I couldn't help but print the design straight away although you suggested checking it first but it really fits perfectly. https://ibb.co/fGbpQK9

Great , glad ur happy , would really help if you post in the groups showing your addition , in case anyone else is after one, and helps promote my files. Thanks.

Could you put the ptfe tubes in and alight it in the position you feel you need, as I think you will find that it will be too low at the bottom. A photo of that would help, are you saying that at the moment it won’t attach or that you don’t like the look of it in that position ?

Of course , give me a day and will upload for you

Hi, Ive uploaded a 14mm option, please print one part first to ensure is ok, as I have no option to test, Ive adapted the drawing

works great, thanks for adding

Whatever length you desire :-)

I needed this answer before I ordered Carbon fiber tubes. I ordered 50 cm tubes and cut them to 37 cm. The hood stays open. you could cut them to 33 cm and remove full size reels, but the hood closes under its own weight.

Unfortunately I replied above your question Rather than too your question , apology’s , I had to re-reply as the site kept prompting me to answer questions I thought I’d already answered

Cool, cool. BTW, love your AMS stand. It works great.

The small tabs are at the bottom to stop the phone falling out and act as a shelf , if you pushed your phone into it then it’s no surprise you damaged the case , the design is exactly like a brodit mount without the width. As you are aware there are many cases available and you can adjust the dimensions using your slicer. If you give me the width and depth of your cased device I will upload one for you

I did not push the phone down, it broke over time driving with the phone in the mount. I feel like the tabs at the buttom of the holder could be much more rounded, solid and maybe 5-10mm wide. I would be very happy if you can make the tabs in a way that the phone/case won't be damaged by design.

There is nothing wrong with the design , I have been using it for 18 months , if it’s not suitable you are welcome to remesh it, I will not be providing you the cad file. If you want me to adapt for your case as I’ve previously offered I will do so , please provide dimensions.

Numbers 1 to 4 of a matching set twice (for each side)

Its would be over twice the height of the printer , do you feel there is a serious requirement ?

yes for at least 3 ams 4 might be to tall,I do not have mine sitting on the top but next to the printers,I will add a photo if there is a makes section

There is now a option you can stack using poles

No sorry I can’t as they vary depending what combination you select

yes indeed, i can only guess ppl put them in sideways ? can you try a bambu spool ? theve send you some with the ams. lets message on fb, i decided to not print extension but to reprint everythin

Glad this was resolved

I use esun spools , if you wish to be able to open fully you should print the 65mm extension , how much longer do you think you need to open ? I can adapt if you you if you wished to reprint , let me know.

ill try with the long extensions first thx. I still find it strange that its impossible to put bambu spools in it by default. If I reprint it all ive wasted alot of filament. ill let you know- thank you

Sorry I don’t understand your question, and please only ask once as I have to reply to each message else cults keep spamming me

I wanted to figure out which way to print them. If I have to rotate them relative to the position of the zip package.

As per the print recommendations in the description , for strength it’s recommended to print flat on their sides as it will ensure the stresses are opposing the layer lines.

Hi , I assuming you are using the extensions already as part of the download , what additional height would you like adding to the extensions offered , I am sure I can adjust and upload for you

Hi, Yeah I'm already using the extensions. I'm not sure how much additional height but I think there needs to be about 45cm in total clearance so the lid can fully open. Many thanks, I really appreciate it :)

Once you assertain what you need to be extended by , let me know , I don’t use the extensions, they were provided on spec by a previous purchasers request.

Just got a notification of an update with 65mm extensions. Thank you very much :)

You are very welcome , I haven’t taken any measurements , I’ve just added 50mm to the 15mm one

I'm sure it will be fine, i'll just confirm for you in the coming days when I get round to printing them (I have to re-print everything because I glued it all together and the top part needs re-doing for the latest version of the AMS you released previously) :)

Hi, just some feedback, printed a couple of them now and they are great! Thanks very much!

Glad ur happy dude , does it open sufficiently for you?

Yeah it opens fully which is exactly what I wanted. I could still load filament previously easily enough, it was just a little annoying having to hold it open. It's perfect for me now. Appreciate your time in doing that for me :)

Welco e

You are the only one to ask for instructions , if you aim for it to look like the pictures it should be pretty obvious

If you need to chat, search for the stands in the official Bambu Facebook group and search for the stands, and you can then contact me via Facebook messenger , you can send me photos and I will assist you on there , thanks

There is no rule when to use and when not to use , someone requested bottom struts , so I added to the print for free, some prefer the peace of mind.

Only one payment is recorded under your username for the rotator.

Can you send me a screen shot please , I printed these without issue the only part in the air is the curved edge which while I recommend support, can be done without . If you join the official Facebook bambu xc1 group and search for the wall mounts you can use that to contact me. Sorry ur having problems I will always do all I can to rectify. Thanks Andy

Thanks I sent you a message on Facebook.

Corresponded , please can we continue on there as rules to payment are that I have to continue to reply to each comment ;-)

Thanks for testing and helping make it compatible for the different unit , wouldn’t of know about it or been able to design the changes without your help, much appreciated.

Needed the updated model for my AMS as well. I did have to add support blockers to the cutouts for the ribs though. The X1C had no problem bridging that length. Thank you for the update.

I could find nothing from bambu on different moulds, all 3 of mine have been identical, without the help of Daniel above this wouldn't of been possible as there were no reference images for me to work from. I hope this provides what you need.

Hi, any will work , the sites been playing up and uploads have failed, but appears it’s been advising that uploads have been made for each failed attempt, all I’ve uploaded are 2 extenders for the more squared version as people had larger reels , to be most compatible I would prob print the PTs saying 1cm longer , however if you have printed the others I have uploaded extenders both with a inner only connection, or the v2 which have a outer lip as well to increase ridigity . Both work.

Hi, any will work , the sites been playing up and uploads have failed, but appears it’s been advising that uploads have been made for each failed attempt, all I’ve uploaded are 2 extenders for the more squared version as people had larger reels , to be most compatible I would prob print the PTs saying 1cm longer , however if you have printed the others I have uploaded extenders both with a inner only connection, or the v2 which have a outer lip as well to increase ridigity . Both work.

Hi, any will work , the sites been playing up and uploads have failed, but appears it’s been advising that uploads have been made for each failed attempt, all I’ve uploaded are 2 extenders for the more squared version as people had larger reels , to be most compatible I would prob print the PTs saying 1cm longer , however if you have printed the others I have uploaded extenders both with a inner only connection, or the v2 which have a outer lip as well to increase ridigity . Both work.

Hi, any will work , the sites been playing up and uploads have failed, but appears it’s been advising that uploads have been made for each failed attempt, all I’ve uploaded are 2 extenders for the more squared version as people had larger reels , to be most compatible I would prob print the PTs saying 1cm longer , however if you have printed the others I have uploaded extenders both with a inner only connection, or the v2 which have a outer lip as well to increase ridigity . Both work.