Skip to content

Vario Lynx 1:8 external scale detail parts.

3D model description

This is a list of many panel doublers and other scale detail for the Vario Lynx fuselage.

Also check out my other Vario Lynx accessories:
http://cults3d.com/en/various/replacement-nose-for-the-vario-lynx
http://cults3d.com/en/various/vario-lynx-1-8-scale-cabin-and-cockpit-doors
http://cults3d.com/en/various/vario-lynx-cockpit-interior
http://cults3d.com/en/various/scale-helicopter-seats-westland-lynx-1-8-seats

Lynxguide.zip - Photos showing the placement on my Lynx.Should be better wuality than the ones shown here.
Wheellock01.stl - Dummy wheel locks for one main and one nose wheel.
Wheel01-03 - Wheels and tires for the nose and main wheels.
Antenna01.stl - Belly antenna and collector tank covers.
Ice01.stl - Ice accretion indicator for right side under cockpit door.
Pitot01.stl - Pitot tube.
Flotation01.stl - Front flotation bags.
Tiedown01.stl - Sponson tie down shackle.
Tiedown02.stl - Nose tie down shackle.
HF01.stl - Forward HF antenna with mounting base.
Fuelvent01.stl - Fuel ventilation pipe.
Sidestores01.stl - Bottom side stores eyelets and belly panels.
Sidestores02.stl - Top side stores eyelets.
Footstep01.stl - Fuselage side footsteps.
Mainfuel01.stl - Main fuel tank panels and air intakes for aft compartment.
Fuelcap01.stl - Main tank gravity fuel filling ports.
Cockpitdoor01.stl - Dummy cockpit doors, handles and latch (for locking in open position).
Wiper01.stl - Windshield wipers.

Rooffairing01.stl - Extension for the bump between the roof windows. Requires adaptation and filling.
Roofpanel01.stl - Panel in front of sliding fairing (doghouse).
AC-intake01.stl - AC generator air intake for roof fairing front.
Sliding01.stl - Rail stop in front of roof sliding fairing
MGB-footstep01.stl - Dummy footstep panels.
Collar01.stl - Filleted ring for blending the area around the main rotor.

Nose03.stl - Douple panels for the joint between the nose and fuelage, bottom and top pieces.
Panel01.stl - Panel doublers fuselage sides below engine cowlings.
Panel02.stl - Panel doublers fuselage sides in front of tail joint.
Panel04.stl - Panel doublers in front of and behind cockpit doors.
Panel06.stl - Panel doublers fuselage sides along panel line.
Panel11.stl - Inset panel under cabin doors.
Navlight01.stl - Cockpit footsteps and nav light units.
Extpower01.stl - External power panel.
Fuelpanel01.stl - Fuel pressure filling access panel for right side.

Aftcompartment01.stl - Aft compartment door.
Nosegearfairing01.stl - Fairing that fits around the nose gear.
Nosegearfairing02.stl - Same as above, but with larger hole if needed.
Sponson01.stl - Root trailing edge fillets for the sponsons. Remove material to fit them.

Exhaust01.stl - Shapes for creating filleted openings for the ducts.
Exhaust02.stl - Exhaust ducts for 50 mm fan.
Tailfairing01.stl - Covers between exhaust duct fairings.
Intake01.stl - Engine air intake leading edge and detail parts.
Coolerintakes01.stl - Engine oil cooler and accessories cooler intakes.
Engcowllock01.stl - Guides for wire lock on the top between the engine cowlings.
Bump01.stl - Bumps and doublers for the engine cowlings.
Enghandle01.stl - Engine cowling locking handles and bump stops.

IGB01.stl - Tail intermediate gearbox fairing parts.
Tailplane01.stl - Shortened tail plane with gourney flap.
Shaftcover01.stl - Tail drive shaft cover doublers. Glue over the tail shaft bump on the tail.
Trailingedge01.stl - Access panels for the left side of the tail fin trailing edge fairing.
Tailpanel01.stl - Lifting holes and doublers for the tail boom.
Tailpanel02.stl - Tail fish plate and tail fin doublers for left side.
Tailpanel03.stl - Tail fish plate and tail fin doublers for right side.
Tailpanel04.stl - Overlapping panel for the tail boom.
Tailpanel05.stl - Overlapping panel for the tail boom. Trim length to fit in the rear.
Tailpanel06.stl - Overlapping panel for the tail boom. Trim length to fit in the rear.
Antenna02.stl - Tail boom bottom center antenna.
HF02.stl - Middle and rear HF antenna posts.
Anticollision01.stl - Anti collision lights for the top of the tail.

3D printing settings

Print as they open. I usually print small parts with 100% infill.

  • 3D model format: STL et ZIP

Tags

Creator

Norwegian inventor/designer/cat owner.

Share

Copyright

Similar creations


Add a comment